If the MAC controller does not connect to any PHY interface, there is a
missing clock, then the DMA reset fails.
For this case, the DMA_BUS_MODE_SFT_RESET bit is 1 before software reset,
just print an error message which gives a hint the PHY clock is missing,
and then return -EINVAL immediately to avoid waiting for the timeout when
the DMA reset fails in loongson_dwmac_fix_reset().
With this patch, for the normal end user, the computer start faster with
reducing boot time for 2 seconds on the specified mainboard.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://patch.msgid.link/20250811073506.27513-4-yangtiezhu@loongson.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Add the interrupt enable register offset (inten_offset) so that GPIO
interrupts can be enabled normally on more models.
According to the latest interface specifications, the definition of GPIO
interrupts in ACPI is similar to that in FDT. The GPIO interrupts are
listed one by one according to the GPIO number, and the corresponding
interrupt number can be obtained directly through the GPIO number
specified by the consumer.
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20250714064542.2276247-1-zhoubinbin@loongson.cn
[Bartosz: tweaked the commit message]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
'struct thermal_zone_device_ops' could be left unmodified in this driver.
Constifying this structure moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
This partly reverts commit 734b5def91b5 ("thermal/drivers/loongson2: Add
Loongson-2K2000 support") which removed the const qualifier. Instead,
define two different structures.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
5089 1160 0 6249 1869 drivers/thermal/loongson2_thermal.o
After:
=====
text data bss dec hex filename
5464 1128 0 6592 19c0 drivers/thermal/loongson2_thermal.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/5f5f815f85a9450bca7848c6d47a1fee840f47e5.1748176328.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Without correct unregisteration, ACPI notify handlers and the platform
drivers installed by generic_subdriver_init() will become dangling
references after removing the loongson_laptop module, triggering various
kernel faults when a hotkey is sent or at kernel shutdown.
Cc: stable@vger.kernel.org
Fixes: 6246ed09111f ("LoongArch: Add ACPI-based generic laptop driver")
Signed-off-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
loongson_laptop_turn_{on,off}_backlight() are designed for controlling
the power of the backlight, but they aren't really used in the driver
previously.
Unify these two functions since they only differ in arguments passed to
ACPI method, and wire up loongson_laptop_backlight_update() to update
the power state of the backlight as well. Tested on the TongFang L860-T2
Loongson-3A5000 laptop.
Cc: stable@vger.kernel.org
Fixes: 6246ed09111f ("LoongArch: Add ACPI-based generic laptop driver")
Signed-off-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Previously during driver probe, 1 is unconditionally taken as current
brightness value and set to props.brightness, which will be considered
as the brightness before suspend and restored to EC on resume. Since a
brightness value of 1 almost never matches EC's state on coldboot (my
laptop's EC defaults to 80), this causes surprising changes of screen
brightness on the first time of resume after coldboot.
Let's get brightness from EC and take it as the current brightness on
probe of the laptop driver to avoid the surprising behavior. Tested on
TongFang L860-T2 Loongson-3A5000 laptop.
Cc: stable@vger.kernel.org
Fixes: 6246ed09111f ("LoongArch: Add ACPI-based generic laptop driver")
Signed-off-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
After commit a934a57a42f64a4 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") and 7d95680d64ac8e836c ("scripts/misc-check:
check unnecessary #include <linux/export.h> when W=1"), we get some build
warnings with W=1:
drivers/spi/spi-loongson-core.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
So fix these build warnings for SPI/Loongson.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/20250608142939.172108-1-chenhuacai@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Add support for the stackleak feature. It initializes the stack with the
poison value before returning from system calls which improves the kernel
security.
At the same time, disables the plugin in EFI stub code because EFI stub
is out of scope for the protection.
Tested on Loongson-3A5000 (enable GCC_PLUGIN_STACKLEAK and LKDTM):
# echo STACKLEAK_ERASING > /sys/kernel/debug/provoke-crash/DIRECT
# dmesg
lkdtm: Performing direct entry STACKLEAK_ERASING
lkdtm: stackleak stack usage:
high offset: 320 bytes
current: 448 bytes
lowest: 1264 bytes
tracked: 1264 bytes
untracked: 208 bytes
poisoned: 14528 bytes
low offset: 64 bytes
lkdtm: OK: the rest of the thread stack is properly erased
Signed-off-by: Youling Tang <tangyouling@kylinos.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Add a new multi-chan IP core (0x12) support which is used in Loongson-
2K3000/Loongson-3B6000M. Compared with the 0x10 core, the new 0x12 core
reduces channel numbers from 8 to 4, but checksum is supported for all
channels.
Add a "multichan" flag to loongson_data, so that we can simply use a
"if (ld->multichan)" condition rather than the complicated condition
"if (ld->loongson_id == DWMAC_CORE_MULTICHAN_V1 || ld->loongson_id ==
DWMAC_CORE_MULTICHAN_V2)".
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Henry Chen <chenx97@aosc.io>
Tested-by: Biao Dong <dongbiao@loongson.cn>
Signed-off-by: Baoqi Zhang <zhangbaoqi@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Link: https://patch.msgid.link/20250424072209.3134762-3-chenhuacai@loongson.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
1.Fix the issue of the SD card crashing due to repeated plugging and unplugging.
2.add init-polarity to support setup init pwm status
3.loongson2_thermal: update temperature formula
4.Fix alert/critical temperature to 75/105
5.Add alientek-2k300 support
The GPIO library will parse the respective property to fill ngpio.
No need to repeat it in the driver.
While at it, drop unused fwnode field.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Functions prefixed with "pcim_" are managed devres functions which
perform automatic cleanup once the driver unloads. It is, thus, not
necessary to call any cleanup functions in remove() callbacks.
Remove the pcim_ cleanup function calls in the remove() callbacks.
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Tested-by: Henry Chen <chenx97@aosc.io>
loongson_dwmac_probe() contains a loop which doesn't have an effect,
because it tries to call pcim_iomap_regions() with the same parameters
several times. The break statement at the loop's end furthermore ensures
that the loop only runs once anyways.
Remove the surplus loop.
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Tested-by: Henry Chen <chenx97@aosc.io>
pcim_iomap_regions() should receive the driver's name as its third
parameter, not the PCI device's name.
Define the driver name with a macro and use it at the appropriate
places, including pcim_iomap_regions().
Cc: stable@vger.kernel.org # v5.14+
Fixes: 30bba69d7db4 ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Tested-by: Henry Chen <chenx97@aosc.io>
According to the chip manual, the I2C register access type of
Loongson-2K2000/LS7A is "B", so we can only access registers in byte
form (readb()/writeb()).
Although Loongson-2K0500/Loongson-2K1000 do not have similar
constraints, register accesses in byte form also behave correctly.
Also, in hardware, the frequency division registers are defined as two
separate registers (high 8-bit and low 8-bit), so we just access them
directly as bytes.
Cc: stable@vger.kernel.org
Fixes: 015e61f0bffd ("i2c: ls2x: Add driver for Loongson-2K/LS7A I2C controller")
Co-developed-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
maoxiaochuan