mirror of
https://gitee.com/open-loongarch/linux-6.12.git
synced 2026-10-25 12:37:11 +08:00
update to 68887137c5
1.Add 2K1000 support 2.Icrease the success rate of download wifi firmware(especially in alpine).
This commit is contained in:
maoxiaochuan
@@ -0,0 +1,918 @@
|
||||
// SPDX-License-Identifier: GPL-2.0
|
||||
/*
|
||||
* Copyright (C) 2023 Loongson Technology Corporation Limited
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
#include <dt-bindings/clock/loongson,ls2k-clk.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
|
||||
/ {
|
||||
#address-cells = <2>;
|
||||
#size-cells = <2>;
|
||||
|
||||
cpus {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
cpu0: cpu@0 {
|
||||
compatible = "loongson,la264";
|
||||
device_type = "cpu";
|
||||
reg= <0x0>;
|
||||
clocks = <&clk LOONGSON2_NODE_CLK>;
|
||||
};
|
||||
|
||||
cpu1: cpu@1 {
|
||||
compatible = "loongson,la264";
|
||||
device_type = "cpu";
|
||||
reg = <0x1>;
|
||||
clocks = <&clk LOONGSON2_NODE_CLK>;
|
||||
};
|
||||
};
|
||||
|
||||
ref_100m: clock-ref-100m {
|
||||
compatible = "fixed-clock";
|
||||
#clock-cells = <0>;
|
||||
clock-frequency = <100000000>;
|
||||
clock-output-names = "ref_100m";
|
||||
};
|
||||
|
||||
cpuintc: interrupt-controller {
|
||||
compatible = "loongson,cpu-interrupt-controller";
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-controller;
|
||||
};
|
||||
|
||||
/* i2c of the dvi eeprom edid */
|
||||
i2c-gpio-0 {
|
||||
compatible = "i2c-gpio";
|
||||
scl-gpios = <&gpio0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
sda-gpios = <&gpio0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
i2c-gpio,delay-us = <5>; /* ~100 kHz */
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
/* i2c of the eeprom edid */
|
||||
i2c-gpio-1 {
|
||||
compatible = "i2c-gpio";
|
||||
scl-gpios = <&gpio0 33 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
sda-gpios = <&gpio0 32 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
i2c-gpio,delay-us = <5>; /* ~100 kHz */
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
thermal-zones {
|
||||
cpu-thermal {
|
||||
polling-delay-passive = <1000>;
|
||||
polling-delay = <5000>;
|
||||
thermal-sensors = <&tsensor 0>;
|
||||
|
||||
trips {
|
||||
cpu_alert: cpu-alert {
|
||||
temperature = <33000>;
|
||||
hysteresis = <2000>;
|
||||
type = "active";
|
||||
};
|
||||
|
||||
cpu_crit: cpu-crit {
|
||||
temperature = <85000>;
|
||||
hysteresis = <5000>;
|
||||
type = "critical";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
bus@10000000 {
|
||||
compatible = "simple-bus";
|
||||
ranges = <0x0 0x10000000 0x0 0x10000000 0x0 0x10000000>,
|
||||
<0x0 0x02000000 0x0 0x02000000 0x0 0x02000000>,
|
||||
<0x0 0x20000000 0x0 0x20000000 0x0 0x10000000>,
|
||||
<0x0 0x40000000 0x0 0x40000000 0x0 0x40000000>,
|
||||
<0xfe 0x0 0xfe 0x0 0x0 0x40000000>;
|
||||
#address-cells = <2>;
|
||||
#size-cells = <2>;
|
||||
dma-coherent;
|
||||
|
||||
isa@18000000 {
|
||||
compatible = "isa";
|
||||
#size-cells = <1>;
|
||||
#address-cells = <2>;
|
||||
ranges = <1 0x0 0x0 0x18000000 0x4000>;
|
||||
};
|
||||
|
||||
liointc0: interrupt-controller@1fe01400 {
|
||||
compatible = "loongson,liointc-2.0";
|
||||
reg = <0x0 0x1fe01400 0x0 0x40>,
|
||||
<0x0 0x1fe01040 0x0 0x8>,
|
||||
<0x0 0x1fe01140 0x0 0x8>;
|
||||
reg-names = "main", "isr0", "isr1";
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
interrupt-parent = <&cpuintc>;
|
||||
interrupts = <2>;
|
||||
interrupt-names = "int0";
|
||||
loongson,parent_int_map = <0xffffffff>, /* int0 */
|
||||
<0x00000000>, /* int1 */
|
||||
<0x00000000>, /* int2 */
|
||||
<0x00000000>; /* int3 */
|
||||
};
|
||||
|
||||
liointc1: interrupt-controller@1fe01440 {
|
||||
compatible = "loongson,liointc-2.0";
|
||||
reg = <0x0 0x1fe01440 0x0 0x40>,
|
||||
<0x0 0x1fe01048 0x0 0x8>,
|
||||
<0x0 0x1fe01148 0x0 0x8>;
|
||||
reg-names = "main", "isr0", "isr1";
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
interrupt-parent = <&cpuintc>;
|
||||
interrupts = <3>;
|
||||
interrupt-names = "int1";
|
||||
loongson,parent_int_map = <0x00000000>, /* int0 */
|
||||
<0xffffffff>, /* int1 */
|
||||
<0x00000000>, /* int2 */
|
||||
<0x00000000>; /* int3 */
|
||||
};
|
||||
|
||||
chipid@1fe00000 {
|
||||
compatible = "loongson,ls2k-chipid";
|
||||
reg = <0x0 0x1fe00000 0x0 0x30>;
|
||||
little-endian;
|
||||
};
|
||||
|
||||
pctrl: pinctrl@1fe00420 {
|
||||
compatible = "loongson,ls2k-pinctrl";
|
||||
reg = <0x0 0x1fe00420 0x0 0x18>;
|
||||
|
||||
gmac1_default:gmac1 {
|
||||
mux {
|
||||
groups ="gmac1";
|
||||
function ="gmac1";
|
||||
};
|
||||
};
|
||||
|
||||
hda_default:hda {
|
||||
mux {
|
||||
groups ="hda_i2s";
|
||||
function ="hda";
|
||||
};
|
||||
};
|
||||
|
||||
hda_as_gpio:hda_as_gpio {
|
||||
mux {
|
||||
groups ="hda_i2s";
|
||||
function ="gpio";
|
||||
};
|
||||
};
|
||||
|
||||
i2s_default:i2s {
|
||||
mux {
|
||||
groups ="hda_i2s";
|
||||
function ="i2s";
|
||||
};
|
||||
};
|
||||
|
||||
ahci_default:ahci {
|
||||
mux {
|
||||
groups ="sata_led";
|
||||
function ="sata_led";
|
||||
};
|
||||
};
|
||||
|
||||
ahci_led_as_gpio:ahci_led_as_gpio {
|
||||
mux {
|
||||
groups ="sata_led";
|
||||
function ="gpio";
|
||||
};
|
||||
};
|
||||
|
||||
pwm0_default:pwm0 {
|
||||
mux {
|
||||
groups ="pwm0";
|
||||
function ="pwm0";
|
||||
};
|
||||
};
|
||||
|
||||
pwm0_as_gpio:pwm0_as_gpio {
|
||||
mux {
|
||||
groups ="pwm0";
|
||||
function ="gpio";
|
||||
};
|
||||
};
|
||||
|
||||
pwm1_default:pwm1 {
|
||||
mux {
|
||||
groups ="pwm1";
|
||||
function ="pwm1";
|
||||
};
|
||||
};
|
||||
|
||||
pwm1_as_gpio:pwm1_as_gpio {
|
||||
mux {
|
||||
groups ="pwm1";
|
||||
function ="gpio";
|
||||
};
|
||||
};
|
||||
|
||||
pwm2_default:pwm2 {
|
||||
mux {
|
||||
groups ="pwm2";
|
||||
function ="pwm2";
|
||||
};
|
||||
};
|
||||
|
||||
pwm2_as_gpio:pwm2_as_gpio {
|
||||
mux {
|
||||
groups ="pwm2";
|
||||
function ="gpio";
|
||||
};
|
||||
};
|
||||
|
||||
pwm3_default:pwm3 {
|
||||
mux {
|
||||
groups ="pwm3";
|
||||
function ="pwm3";
|
||||
};
|
||||
};
|
||||
|
||||
pwm3_as_gpio:pwm3_as_gpio {
|
||||
mux {
|
||||
groups ="pwm3";
|
||||
function ="gpio";
|
||||
};
|
||||
};
|
||||
|
||||
uart0_4_default:uart0_4{
|
||||
mux {
|
||||
groups = "uart0";
|
||||
function = "uart0_4";
|
||||
};
|
||||
};
|
||||
|
||||
uart1_4_default:uart1_4 {
|
||||
mux {
|
||||
groups = "uart1";
|
||||
function = "uart1_4";
|
||||
};
|
||||
};
|
||||
|
||||
uart2_4_default:uart2_4 {
|
||||
mux {
|
||||
groups = "uart2";
|
||||
function = "uart2_4";
|
||||
};
|
||||
};
|
||||
|
||||
dvo0_default:dvo0 {
|
||||
mux {
|
||||
groups = "dvo0_lio_uart";
|
||||
function = "dvo0";
|
||||
};
|
||||
};
|
||||
|
||||
dvo1_default:dvo1 {
|
||||
mux {
|
||||
groups = "dvo1_camera";
|
||||
function = "dvo1";
|
||||
};
|
||||
};
|
||||
|
||||
can0_default:can0 {
|
||||
mux {
|
||||
groups = "can0";
|
||||
function = "can0";
|
||||
};
|
||||
};
|
||||
|
||||
can1_default:can1 {
|
||||
mux {
|
||||
groups = "can1";
|
||||
function = "can1";
|
||||
};
|
||||
};
|
||||
|
||||
can1_as_gpio:can1_as_gpio {
|
||||
mux {
|
||||
groups = "can1";
|
||||
function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
sdio_gpio:sdio {
|
||||
mux {
|
||||
groups = "sdio";
|
||||
function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
lio_default:lio {
|
||||
mux {
|
||||
groups = "dvo0_lio_uart";
|
||||
function = "lio";
|
||||
};
|
||||
};
|
||||
|
||||
i2c0_as_gpio:i2c0_as_gpio {
|
||||
mux {
|
||||
groups = "i2c0";
|
||||
function = "gpio";
|
||||
};
|
||||
};
|
||||
i2c1_as_gpio:i2c1_as_gpio {
|
||||
mux {
|
||||
groups = "i2c1";
|
||||
function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
clk: clock-controller@1fe00480 {
|
||||
compatible = "loongson,ls2k-clk";
|
||||
reg = <0x0 0x1fe00480 0x0 0x58>;
|
||||
#clock-cells = <1>;
|
||||
clocks = <&ref_100m>;
|
||||
clock-names = "ref_100m";
|
||||
};
|
||||
|
||||
gpio0: gpio@1fe00500 {
|
||||
compatible = "loongson,ls2k-gpio";
|
||||
reg = <0x0 0x1fe00500 0x0 0x38>;
|
||||
ngpios = <64>;
|
||||
#gpio-cells = <2>;
|
||||
gpio-controller;
|
||||
gpio-ranges = <&pctrl 0x0 0x0 15>,
|
||||
<&pctrl 16 16 15>,
|
||||
<&pctrl 32 32 10>,
|
||||
<&pctrl 44 44 20>;
|
||||
interrupt-parent = <&liointc1>;
|
||||
interrupts = <28 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<29 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<30 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<30 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<26 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<>,
|
||||
<>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<27 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
|
||||
tsensor: thermal-sensor@1fe01500 {
|
||||
compatible = "loongson,ls2k1000-thermal";
|
||||
reg = <0x0 0x1fe01500 0x0 0x30>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
|
||||
#thermal-sensor-cells = <1>;
|
||||
};
|
||||
|
||||
apbdma0: dma-controller@1fe00c00 {
|
||||
compatible = "loongson,ls2k1000-apbdma";
|
||||
reg = <0x0 0x1fe00c00 0x0 0x8>;
|
||||
interrupt-parent = <&liointc1>;
|
||||
interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
#dma-cells = <1>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
apbdma1: dma-controller@1fe00c10 {
|
||||
compatible = "loongson,ls2k1000-apbdma";
|
||||
reg = <0x0 0x1fe00c10 0x0 0x8>;
|
||||
interrupt-parent = <&liointc1>;
|
||||
interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
#dma-cells = <1>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
apbdma2: dma-controller@1fe00c20 {
|
||||
compatible = "loongson,ls2k1000-apbdma";
|
||||
reg = <0x0 0x1fe00c20 0x0 0x8>;
|
||||
interrupt-parent = <&liointc1>;
|
||||
interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
#dma-cells = <1>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
apbdma3: dma-controller@1fe00c30 {
|
||||
compatible = "loongson,ls2k1000-apbdma";
|
||||
reg = <0x0 0x1fe00c30 0x0 0x8>;
|
||||
interrupt-parent = <&liointc1>;
|
||||
interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
#dma-cells = <1>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
dma-controller@1fe00c40 {
|
||||
compatible = "loongson,ls2k1000-apbdma";
|
||||
reg = <0x0 0x1fe00c40 0x0 0x8>;
|
||||
interrupt-parent = <&liointc1>;
|
||||
interrupts = <16 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
#dma-cells = <1>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
uart0: serial@1fe20000 {
|
||||
compatible = "ns16550a";
|
||||
reg = <0x0 0x1fe20000 0x0 0x10>;
|
||||
clock-frequency = <125000000>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <0x0 IRQ_TYPE_LEVEL_HIGH>;
|
||||
no-loopback-test;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
uart1: serial@0x1fe20100 {
|
||||
compatible = "ns16550a";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart1_4_default>;
|
||||
reg = <0 0x1fe20100 0 0x10>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <0x0 IRQ_TYPE_LEVEL_HIGH>;
|
||||
no-loopback-test;
|
||||
status = "disable"
|
||||
};
|
||||
|
||||
uart2: serial@0x1fe20200 {
|
||||
compatible = "ns16550a";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart2_4_default>;
|
||||
reg = <0 0x1fe20200 0 0x10>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <0x0 IRQ_TYPE_LEVEL_HIGH>;
|
||||
no-loopback-test;
|
||||
status = "disable"
|
||||
};
|
||||
|
||||
uart3: serial@0x1fe20300 {
|
||||
compatible = "ns16550a";
|
||||
reg = <0 0x1fe20300 0 0x10>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <0x0 IRQ_TYPE_LEVEL_HIGH>;
|
||||
no-loopback-test;
|
||||
status = "disable"
|
||||
};
|
||||
|
||||
uart4: serial@0x1fe20400 {
|
||||
compatible = "ns16550a";
|
||||
reg = <0 0x1fe20400 0 0x10>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <0x1 IRQ_TYPE_LEVEL_HIGH>;
|
||||
no-loopback-test;
|
||||
status = "disable"
|
||||
};
|
||||
|
||||
uart5: serial@0x1fe20500 {
|
||||
compatible = "ns16550a";
|
||||
reg = <0 0x1fe20500 0 0x10>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <0x1 IRQ_TYPE_LEVEL_HIGH>;
|
||||
no-loopback-test;
|
||||
status = "disable"
|
||||
};
|
||||
|
||||
uart6: serial@0x1fe20600 {
|
||||
compatible = "ns16550a";
|
||||
reg = <0 0x1fe20600 0 0x10>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <0x1 IRQ_TYPE_LEVEL_HIGH>;
|
||||
no-loopback-test;
|
||||
status = "disable"
|
||||
};
|
||||
|
||||
uart7: serial@0x1fe20700 {
|
||||
compatible = "ns16550a";
|
||||
reg = <0 0x1fe20700 0 0x10>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <0x1 IRQ_TYPE_LEVEL_HIGH>;
|
||||
no-loopback-test;
|
||||
status = "disable"
|
||||
};
|
||||
|
||||
uart8: serial@0x1fe20800 {
|
||||
compatible = "ns16550a";
|
||||
reg = <0 0x1fe20800 0 0x10>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <0x2 IRQ_TYPE_LEVEL_HIGH>;
|
||||
no-loopback-test;
|
||||
status = "disable"
|
||||
};
|
||||
|
||||
uart9: serial@0x1fe20900 {
|
||||
compatible = "ns16550a";
|
||||
reg = <0 0x1fe20900 0 0x10>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <0x2 IRQ_TYPE_LEVEL_HIGH>;
|
||||
no-loopback-test;
|
||||
status = "disable"
|
||||
};
|
||||
|
||||
uart10: serial@0x1fe20a00 {
|
||||
compatible = "ns16550a";
|
||||
reg = <0 0x1fe20a00 0 0x10>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <0x2 IRQ_TYPE_LEVEL_HIGH>;
|
||||
no-loopback-test;
|
||||
status = "disable"
|
||||
};
|
||||
|
||||
uart11: serial@0x1fe20b00 {
|
||||
compatible = "ns16550a";
|
||||
reg = <0 0x1fe20b00 0 0x10>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <0x2 IRQ_TYPE_LEVEL_HIGH>;
|
||||
no-loopback-test;
|
||||
status = "disable"
|
||||
};
|
||||
|
||||
i2c2: i2c@1fe21000 {
|
||||
compatible = "loongson,ls2k-i2c";
|
||||
reg = <0x0 0x1fe21000 0x0 0x8>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
i2c3: i2c@1fe21800 {
|
||||
compatible = "loongson,ls2k-i2c";
|
||||
reg = <0x0 0x1fe21800 0x0 0x8>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
pmc: power-management@1fe27000 {
|
||||
compatible = "loongson,ls2k1000-pmc", "loongson,ls2k0500-pmc", "syscon";
|
||||
reg = <0x0 0x1fe27000 0x0 0x58>;
|
||||
interrupt-parent = <&liointc1>;
|
||||
interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
|
||||
loongson,suspend-address = <0x0 0x1c000500>;
|
||||
|
||||
syscon-reboot {
|
||||
compatible = "syscon-reboot";
|
||||
offset = <0x30>;
|
||||
mask = <0x1>;
|
||||
};
|
||||
|
||||
syscon-poweroff {
|
||||
compatible = "syscon-poweroff";
|
||||
regmap = <&pmc>;
|
||||
offset = <0x14>;
|
||||
mask = <0x3c00>;
|
||||
value = <0x3c00>;
|
||||
};
|
||||
};
|
||||
|
||||
rtc0: rtc@1fe27800 {
|
||||
compatible = "loongson,ls2k1000-rtc";
|
||||
reg = <0x0 0x1fe27800 0x0 0x100>;
|
||||
interrupt-parent = <&liointc1>;
|
||||
interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
//no driver
|
||||
i2s: i2s@1fe2d000 {
|
||||
compatible = "loongson,ls2k1000-i2s";
|
||||
reg = <0 0x1fe2d000 0 0x14>,
|
||||
<0 0x1fe00438 0 0x8>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
dmas = <&apbdma2 0>, <&apbdma3 0>;
|
||||
dma-names = "tx", "rx";
|
||||
#sound-dai-cells = <0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
spi0: spi@1fff0220 {
|
||||
compatible = "loongson,ls2k1000-spi";
|
||||
reg = <0x0 0x1fff0220 0x0 0x10>;
|
||||
clocks = <&clk LOONGSON2_BOOT_CLK>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
//no driver
|
||||
nand: nand@1fe26040 {
|
||||
#address-cells = <2>;
|
||||
compatible = "loongson,ls-nand";
|
||||
reg = <0 0x1fe26040 0 0x0
|
||||
0 0x1fe26000 0 0x20>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupt-names = "nand_irq";
|
||||
|
||||
dmas = <&apbdma0 1>;
|
||||
dma-names = "nand_rw";
|
||||
dma-mask = <0xffffffff 0xffffffff>;
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
/* CAN controller nodes:
|
||||
* If you want to use the "can" function,enable the "can"
|
||||
* controller by configure general configuration register 0.
|
||||
*/
|
||||
can0: can@1fe20c00{
|
||||
compatible = "nxp,sja1000";
|
||||
reg = <0 0x1fe20c00 0 0xff>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <16 IRQ_TYPE_LEVEL_HIGH>;
|
||||
pinctrl-0 = <&can0_default>;
|
||||
pinctrl-names = "default";
|
||||
status = "disabled";
|
||||
};
|
||||
can1: can@1fe20d00{
|
||||
compatible = "nxp,sja1000";
|
||||
reg = <0 0x1fe20d00 0 0xff>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
|
||||
pinctrl-0 = <&can1_default>;
|
||||
pinctrl-names = "default";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
|
||||
pwm0: pwm@1fe22000{
|
||||
compatible = "loongson,ls2k-pwm";
|
||||
reg = <0 0x1fe22000 0 0x10>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
clock-names = "pwm-clk";
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
|
||||
#pwm-cells = <2>;
|
||||
pinctrl-0 = <&pwm0_default>;
|
||||
pinctrl-names = "default";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
pwm1: pwm@1fe22010{
|
||||
compatible = "loongson,ls2k-pwm";
|
||||
reg = <0 0x1fe22010 0 0x10>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
clock-names = "pwm-clk";
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <25 IRQ_TYPE_LEVEL_HIGH>;
|
||||
#pwm-cells = <2>;
|
||||
pinctrl-0 = <&pwm1_default>;
|
||||
pinctrl-names = "default";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
pwm2: pwm@1fe22020 {
|
||||
compatible = "loongson,ls2k-pwm";
|
||||
|
||||
reg = <0 0x1fe22020 0 0xf>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
clock-names = "pwm-clk";
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <26 IRQ_TYPE_LEVEL_HIGH>; //34- 31
|
||||
|
||||
#pwm-cells = <2>;
|
||||
pinctrl-0 = <&pwm2_default>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
pwm3: pwm@1fe22030 {
|
||||
compatible = "loongson,ls2k-pwm";
|
||||
|
||||
reg = <0 0x1fe22030 0 0xf>;
|
||||
clocks = <&clk LOONGSON2_APB_CLK>;
|
||||
clock-names = "pwm-clk";
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
#pwm-cells = <2>;
|
||||
pinctrl-0 = <&pwm3_default>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
gmac0: ethernet@40040000 {
|
||||
compatible = "snps,dwmac-3.70a";
|
||||
reg = <0 0x40040000 0 0x8000>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <12 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<13 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupt-names = "macirq", "eth_lpi";
|
||||
phy-mode = "rgmii-id";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
gmac1: ethernet@40050000 {
|
||||
compatible = "snps,dwmac-3.70a";
|
||||
reg = <0 0x40050000 0 0x8000>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <14 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<15 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupt-names = "macirq", "eth_lpi";
|
||||
phy-mode = "rgmii-id";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
otg: usb@40000000 {
|
||||
compatible = "loongson,dwc2-otg";
|
||||
reg = <0 0x40000000 0 0x40000>;
|
||||
interrupt-parent = <&liointc1>;
|
||||
interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
|
||||
ehci0: usb@40060000 {
|
||||
compatible = "generic-ehci";
|
||||
reg = <0 0x40060000 0 0x8000>;
|
||||
interrupt-parent = <&liointc1>;
|
||||
interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
|
||||
ohci0: usb@40070000 {
|
||||
compatible = "generic-ohci";
|
||||
reg = <0 0x40070000 0 0x8000>;
|
||||
interrupt-parent = <&liointc1>;
|
||||
interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
|
||||
dc: display@400c0000 {
|
||||
compatible = "loongson,ls2k1000-dc";
|
||||
reg = <0 0x400c0000 0 0x00010000>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <28 IRQ_TYPE_LEVEL_HIGH>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
hda@0x400d0000 {
|
||||
compatible = "loongson,ls2k-audio";
|
||||
reg = <0 0x400d0000 0 0xffff>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
sata: sata@400e0000 {
|
||||
compatible = "snps,spear-ahci";
|
||||
reg = <0 0x400e0000 0 0x10000>;
|
||||
interrupt-parent = <&liointc0>;
|
||||
interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
pcie@1a000000 {
|
||||
compatible = "loongson,ls2k-pci";
|
||||
reg = <0xfe 0x0 0x0 0x20000000>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
device_type = "pci";
|
||||
bus-range = <0x0 0xff>;
|
||||
ranges = <0x01000000 0x0 0x00008000 0x0 0x18008000 0x0 0x00008000>,
|
||||
<0x02000000 0x0 0x60000000 0x0 0x60000000 0x0 0x20000000>;
|
||||
|
||||
pcie@9,0 {
|
||||
reg = <0x4800 0x0 0x0 0x0 0x0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
device_type = "pci";
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0x0 0x0 0x0 0x0>;
|
||||
interrupt-map = <0x0 0x0 0x0 0x0 &liointc1 0x0 IRQ_TYPE_LEVEL_HIGH>;
|
||||
ranges;
|
||||
};
|
||||
|
||||
pcie@a,0 {
|
||||
reg = <0x5000 0x0 0x0 0x0 0x0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
device_type = "pci";
|
||||
interrupt-parent = <&liointc1>;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0x0 0x0 0x0 0x0>;
|
||||
interrupt-map = <0x0 0x0 0x0 0x0 &liointc1 1 IRQ_TYPE_LEVEL_HIGH>;
|
||||
ranges;
|
||||
};
|
||||
|
||||
pcie@b,0 {
|
||||
reg = <0x5800 0x0 0x0 0x0 0x0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
device_type = "pci";
|
||||
interrupt-parent = <&liointc1>;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0x0 0x0 0x0 0x0>;
|
||||
interrupt-map = <0x0 0x0 0x0 0x0 &liointc1 2 IRQ_TYPE_LEVEL_HIGH>;
|
||||
ranges;
|
||||
};
|
||||
|
||||
pcie@c,0 {
|
||||
reg = <0x6000 0x0 0x0 0x0 0x0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
device_type = "pci";
|
||||
interrupt-parent = <&liointc1>;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0x0 0x0 0x0 0x0>;
|
||||
interrupt-map = <0x0 0x0 0x0 0x0 &liointc1 3 IRQ_TYPE_LEVEL_HIGH>;
|
||||
ranges;
|
||||
};
|
||||
|
||||
pcie@d,0 {
|
||||
reg = <0x6800 0x0 0x0 0x0 0x0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
device_type = "pci";
|
||||
interrupt-parent = <&liointc1>;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0x0 0x0 0x0 0x0>;
|
||||
interrupt-map = <0x0 0x0 0x0 0x0 &liointc1 4 IRQ_TYPE_LEVEL_HIGH>;
|
||||
ranges;
|
||||
};
|
||||
|
||||
pcie@e,0 {
|
||||
reg = <0x7000 0x0 0x0 0x0 0x0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
device_type = "pci";
|
||||
interrupt-parent = <&liointc1>;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0x0 0x0 0x0 0x0>;
|
||||
interrupt-map = <0x0 0x0 0x0 0x0 &liointc1 5 IRQ_TYPE_LEVEL_HIGH>;
|
||||
ranges;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
@@ -5,7 +5,7 @@
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "loongson-2k1000.dtsi"
|
||||
#include "loongson2k1000.dtsi"
|
||||
#include "loongson_panel_param.dtsi"
|
||||
#include <dt-bindings/input/linux-event-codes.h>
|
||||
|
||||
@@ -14,6 +14,8 @@
|
||||
|
||||
aliases {
|
||||
serial0 = &uart0;
|
||||
ethernet0 = &gmac0;
|
||||
ethernet1 = &gmac1;
|
||||
};
|
||||
|
||||
chosen {
|
||||
|
||||
@@ -0,0 +1,811 @@
|
||||
CONFIG_LOCALVERSION=".lsgd"
|
||||
# CONFIG_LOCALVERSION_AUTO is not set
|
||||
CONFIG_SYSVIPC=y
|
||||
CONFIG_POSIX_MQUEUE=y
|
||||
CONFIG_NO_HZ=y
|
||||
CONFIG_HIGH_RES_TIMERS=y
|
||||
CONFIG_BPF_SYSCALL=y
|
||||
CONFIG_BPF_JIT=y
|
||||
CONFIG_PREEMPT_RT=y
|
||||
CONFIG_BSD_PROCESS_ACCT=y
|
||||
CONFIG_BSD_PROCESS_ACCT_V3=y
|
||||
CONFIG_TASKSTATS=y
|
||||
CONFIG_TASK_DELAY_ACCT=y
|
||||
CONFIG_TASK_XACCT=y
|
||||
CONFIG_TASK_IO_ACCOUNTING=y
|
||||
CONFIG_LOG_BUF_SHIFT=18
|
||||
CONFIG_MEMCG=y
|
||||
CONFIG_BLK_CGROUP=y
|
||||
CONFIG_CFS_BANDWIDTH=y
|
||||
CONFIG_RT_GROUP_SCHED=y
|
||||
CONFIG_CGROUP_PIDS=y
|
||||
CONFIG_CGROUP_RDMA=y
|
||||
CONFIG_CGROUP_FREEZER=y
|
||||
CONFIG_CGROUP_HUGETLB=y
|
||||
CONFIG_CGROUP_DEVICE=y
|
||||
CONFIG_CGROUP_CPUACCT=y
|
||||
CONFIG_CGROUP_PERF=y
|
||||
CONFIG_CGROUP_BPF=y
|
||||
CONFIG_CGROUP_MISC=y
|
||||
CONFIG_NAMESPACES=y
|
||||
CONFIG_USER_NS=y
|
||||
CONFIG_CHECKPOINT_RESTORE=y
|
||||
CONFIG_SCHED_AUTOGROUP=y
|
||||
CONFIG_RELAY=y
|
||||
CONFIG_BLK_DEV_INITRD=y
|
||||
CONFIG_EXPERT=y
|
||||
CONFIG_KALLSYMS_ALL=y
|
||||
CONFIG_PERF_EVENTS=y
|
||||
CONFIG_KEXEC=y
|
||||
CONFIG_LOONGSON_2K1000=y
|
||||
CONFIG_HZ_1000=y
|
||||
CONFIG_CMDLINE="fbcon=logo-pos:center fbcon=logo-count:1"
|
||||
CONFIG_CMDLINE_EXTEND=y
|
||||
CONFIG_BUILTIN_DTB=y
|
||||
# CONFIG_SCHED_SMT is not set
|
||||
CONFIG_SMP=y
|
||||
CONFIG_NR_CPUS=2
|
||||
# CONFIG_SUSPEND is not set
|
||||
CONFIG_PM=y
|
||||
# CONFIG_ACPI_AC is not set
|
||||
# CONFIG_ACPI_BATTERY is not set
|
||||
# CONFIG_ACPI_BUTTON is not set
|
||||
# CONFIG_ACPI_FAN is not set
|
||||
# CONFIG_ACPI_PROCESSOR is not set
|
||||
# CONFIG_ACPI_TABLE_UPGRADE is not set
|
||||
CONFIG_JUMP_LABEL=y
|
||||
# CONFIG_RANDOMIZE_KSTACK_OFFSET is not set
|
||||
CONFIG_MODULES=y
|
||||
CONFIG_MODULE_FORCE_LOAD=y
|
||||
CONFIG_MODULE_UNLOAD=y
|
||||
CONFIG_MODULE_FORCE_UNLOAD=y
|
||||
CONFIG_MODVERSIONS=y
|
||||
CONFIG_BLK_DEV_INTEGRITY=y
|
||||
CONFIG_BLK_DEV_ZONED=y
|
||||
CONFIG_BLK_DEV_THROTTLING=y
|
||||
CONFIG_BLK_WBT=y
|
||||
CONFIG_BLK_CGROUP_IOLATENCY=y
|
||||
CONFIG_BLK_CGROUP_IOCOST=y
|
||||
CONFIG_BLK_CGROUP_IOPRIO=y
|
||||
CONFIG_PARTITION_ADVANCED=y
|
||||
CONFIG_BSD_DISKLABEL=y
|
||||
CONFIG_UNIXWARE_DISKLABEL=y
|
||||
CONFIG_CMDLINE_PARTITION=y
|
||||
CONFIG_ZSWAP=y
|
||||
CONFIG_ZSWAP_COMPRESSOR_DEFAULT_ZSTD=y
|
||||
CONFIG_ZBUD=y
|
||||
# CONFIG_COMPAT_BRK is not set
|
||||
CONFIG_SPARSEMEM_MANUAL=y
|
||||
CONFIG_PAGE_REPORTING=y
|
||||
CONFIG_KSM=y
|
||||
CONFIG_CMA=y
|
||||
CONFIG_CMA_SYSFS=y
|
||||
CONFIG_CMA_AREAS=20
|
||||
CONFIG_USERFAULTFD=y
|
||||
CONFIG_NET=y
|
||||
CONFIG_PACKET=y
|
||||
CONFIG_UNIX=y
|
||||
CONFIG_TLS=m
|
||||
CONFIG_TLS_DEVICE=y
|
||||
CONFIG_XFRM_USER=y
|
||||
CONFIG_NET_KEY=y
|
||||
CONFIG_XDP_SOCKETS=y
|
||||
CONFIG_INET=y
|
||||
CONFIG_IP_MULTICAST=y
|
||||
CONFIG_IP_ADVANCED_ROUTER=y
|
||||
CONFIG_IP_MULTIPLE_TABLES=y
|
||||
CONFIG_IP_ROUTE_MULTIPATH=y
|
||||
CONFIG_IP_ROUTE_VERBOSE=y
|
||||
CONFIG_IP_PNP=y
|
||||
CONFIG_IP_PNP_DHCP=y
|
||||
CONFIG_IP_PNP_BOOTP=y
|
||||
CONFIG_IP_PNP_RARP=y
|
||||
CONFIG_NET_IPIP=m
|
||||
CONFIG_NET_IPGRE_DEMUX=m
|
||||
CONFIG_NET_IPGRE=m
|
||||
CONFIG_NET_IPGRE_BROADCAST=y
|
||||
CONFIG_IP_MROUTE=y
|
||||
CONFIG_IP_MROUTE_MULTIPLE_TABLES=y
|
||||
CONFIG_IP_PIMSM_V1=y
|
||||
CONFIG_IP_PIMSM_V2=y
|
||||
CONFIG_INET_AH=m
|
||||
CONFIG_INET_ESP=m
|
||||
CONFIG_INET_ESP_OFFLOAD=m
|
||||
CONFIG_INET_ESPINTCP=y
|
||||
CONFIG_INET_IPCOMP=m
|
||||
CONFIG_INET_UDP_DIAG=y
|
||||
CONFIG_TCP_CONG_ADVANCED=y
|
||||
CONFIG_TCP_CONG_BBR=m
|
||||
CONFIG_IPV6_ROUTER_PREF=y
|
||||
CONFIG_IPV6_ROUTE_INFO=y
|
||||
CONFIG_INET6_AH=y
|
||||
CONFIG_INET6_ESP=y
|
||||
CONFIG_INET6_ESP_OFFLOAD=y
|
||||
CONFIG_INET6_ESPINTCP=y
|
||||
CONFIG_INET6_IPCOMP=y
|
||||
CONFIG_IPV6_MULTIPLE_TABLES=y
|
||||
CONFIG_IPV6_MROUTE=y
|
||||
CONFIG_MPTCP=y
|
||||
CONFIG_NETWORK_PHY_TIMESTAMPING=y
|
||||
CONFIG_NETFILTER=y
|
||||
CONFIG_BRIDGE_NETFILTER=m
|
||||
CONFIG_NETFILTER_NETLINK_LOG=m
|
||||
CONFIG_NF_CONNTRACK=m
|
||||
CONFIG_NF_CONNTRACK_AMANDA=m
|
||||
CONFIG_NF_CONNTRACK_FTP=m
|
||||
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
|
||||
CONFIG_NF_CONNTRACK_SNMP=m
|
||||
CONFIG_NF_CONNTRACK_PPTP=m
|
||||
CONFIG_NF_CONNTRACK_TFTP=m
|
||||
CONFIG_NF_CT_NETLINK=m
|
||||
CONFIG_NF_TABLES=m
|
||||
CONFIG_NF_TABLES_INET=y
|
||||
CONFIG_NFT_CT=m
|
||||
CONFIG_NFT_CONNLIMIT=m
|
||||
CONFIG_NFT_LOG=m
|
||||
CONFIG_NFT_LIMIT=m
|
||||
CONFIG_NFT_MASQ=m
|
||||
CONFIG_NFT_REDIR=m
|
||||
CONFIG_NFT_NAT=m
|
||||
CONFIG_NFT_TUNNEL=m
|
||||
CONFIG_NFT_QUEUE=m
|
||||
CONFIG_NFT_QUOTA=m
|
||||
CONFIG_NFT_REJECT=m
|
||||
CONFIG_NFT_COMPAT=m
|
||||
CONFIG_NFT_HASH=m
|
||||
CONFIG_NFT_FIB_INET=m
|
||||
CONFIG_NFT_SOCKET=m
|
||||
CONFIG_NFT_OSF=m
|
||||
CONFIG_NFT_TPROXY=m
|
||||
CONFIG_NETFILTER_XT_SET=m
|
||||
CONFIG_NETFILTER_XT_TARGET_AUDIT=m
|
||||
CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
|
||||
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
|
||||
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
|
||||
CONFIG_NETFILTER_XT_TARGET_CT=m
|
||||
CONFIG_NETFILTER_XT_TARGET_DSCP=m
|
||||
CONFIG_NETFILTER_XT_TARGET_HMARK=m
|
||||
CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
|
||||
CONFIG_NETFILTER_XT_TARGET_LED=m
|
||||
CONFIG_NETFILTER_XT_TARGET_LOG=m
|
||||
CONFIG_NETFILTER_XT_TARGET_MARK=m
|
||||
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
|
||||
CONFIG_NETFILTER_XT_TARGET_TRACE=m
|
||||
CONFIG_NETFILTER_XT_TARGET_SECMARK=m
|
||||
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
|
||||
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
|
||||
CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
|
||||
CONFIG_NETFILTER_XT_MATCH_BPF=m
|
||||
CONFIG_NETFILTER_XT_MATCH_CGROUP=m
|
||||
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
|
||||
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
|
||||
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
|
||||
CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
|
||||
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
|
||||
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
|
||||
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
|
||||
CONFIG_NETFILTER_XT_MATCH_CPU=m
|
||||
CONFIG_NETFILTER_XT_MATCH_DCCP=m
|
||||
CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
|
||||
CONFIG_NETFILTER_XT_MATCH_DSCP=m
|
||||
CONFIG_NETFILTER_XT_MATCH_ESP=m
|
||||
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
|
||||
CONFIG_NETFILTER_XT_MATCH_HELPER=m
|
||||
CONFIG_NETFILTER_XT_MATCH_IPCOMP=m
|
||||
CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
|
||||
CONFIG_NETFILTER_XT_MATCH_IPVS=m
|
||||
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
|
||||
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
|
||||
CONFIG_NETFILTER_XT_MATCH_MAC=m
|
||||
CONFIG_NETFILTER_XT_MATCH_MARK=m
|
||||
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
|
||||
CONFIG_NETFILTER_XT_MATCH_NFACCT=m
|
||||
CONFIG_NETFILTER_XT_MATCH_OSF=m
|
||||
CONFIG_NETFILTER_XT_MATCH_OWNER=m
|
||||
CONFIG_NETFILTER_XT_MATCH_POLICY=m
|
||||
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
|
||||
CONFIG_NETFILTER_XT_MATCH_QUOTA=m
|
||||
CONFIG_NETFILTER_XT_MATCH_RATEEST=m
|
||||
CONFIG_NETFILTER_XT_MATCH_REALM=m
|
||||
CONFIG_NETFILTER_XT_MATCH_SOCKET=m
|
||||
CONFIG_NETFILTER_XT_MATCH_STATE=m
|
||||
CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
|
||||
CONFIG_NETFILTER_XT_MATCH_STRING=m
|
||||
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
|
||||
CONFIG_NETFILTER_XT_MATCH_TIME=m
|
||||
CONFIG_NETFILTER_XT_MATCH_U32=m
|
||||
CONFIG_IP_SET=m
|
||||
CONFIG_IP_VS=m
|
||||
CONFIG_IP_VS_IPV6=y
|
||||
CONFIG_IP_VS_PROTO_TCP=y
|
||||
CONFIG_IP_VS_PROTO_UDP=y
|
||||
CONFIG_IP_VS_PROTO_ESP=y
|
||||
CONFIG_IP_VS_PROTO_AH=y
|
||||
CONFIG_IP_VS_PROTO_SCTP=y
|
||||
CONFIG_IP_VS_RR=m
|
||||
CONFIG_IP_VS_WRR=m
|
||||
CONFIG_IP_VS_NFCT=y
|
||||
CONFIG_NFT_DUP_IPV4=m
|
||||
CONFIG_NFT_FIB_IPV4=m
|
||||
CONFIG_NF_TABLES_ARP=y
|
||||
CONFIG_IP_NF_IPTABLES=m
|
||||
CONFIG_IP_NF_MATCH_AH=m
|
||||
CONFIG_IP_NF_MATCH_ECN=m
|
||||
CONFIG_IP_NF_MATCH_RPFILTER=m
|
||||
CONFIG_IP_NF_MATCH_TTL=m
|
||||
CONFIG_IP_NF_FILTER=m
|
||||
CONFIG_IP_NF_TARGET_REJECT=m
|
||||
CONFIG_IP_NF_TARGET_SYNPROXY=m
|
||||
CONFIG_IP_NF_NAT=m
|
||||
CONFIG_IP_NF_TARGET_MASQUERADE=m
|
||||
CONFIG_IP_NF_TARGET_NETMAP=m
|
||||
CONFIG_IP_NF_TARGET_REDIRECT=m
|
||||
CONFIG_IP_NF_MANGLE=m
|
||||
CONFIG_IP_NF_TARGET_ECN=m
|
||||
CONFIG_IP_NF_TARGET_TTL=m
|
||||
CONFIG_IP_NF_RAW=m
|
||||
CONFIG_IP_NF_SECURITY=m
|
||||
CONFIG_IP_NF_ARPFILTER=m
|
||||
CONFIG_IP_NF_ARP_MANGLE=m
|
||||
CONFIG_NFT_FIB_IPV6=m
|
||||
CONFIG_IP6_NF_IPTABLES=y
|
||||
CONFIG_IP6_NF_MATCH_AH=m
|
||||
CONFIG_IP6_NF_MATCH_EUI64=m
|
||||
CONFIG_IP6_NF_MATCH_FRAG=m
|
||||
CONFIG_IP6_NF_MATCH_OPTS=m
|
||||
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
|
||||
CONFIG_IP6_NF_MATCH_MH=m
|
||||
CONFIG_IP6_NF_MATCH_RPFILTER=m
|
||||
CONFIG_IP6_NF_MATCH_RT=m
|
||||
CONFIG_IP6_NF_MATCH_SRH=m
|
||||
CONFIG_IP6_NF_FILTER=y
|
||||
CONFIG_IP6_NF_TARGET_REJECT=m
|
||||
CONFIG_IP6_NF_TARGET_SYNPROXY=m
|
||||
CONFIG_IP6_NF_MANGLE=m
|
||||
CONFIG_IP6_NF_RAW=m
|
||||
CONFIG_IP6_NF_SECURITY=m
|
||||
CONFIG_IP6_NF_NAT=m
|
||||
CONFIG_IP6_NF_TARGET_MASQUERADE=m
|
||||
CONFIG_IP6_NF_TARGET_NPT=m
|
||||
CONFIG_NF_TABLES_BRIDGE=m
|
||||
CONFIG_NF_CONNTRACK_BRIDGE=m
|
||||
CONFIG_BRIDGE_NF_EBTABLES=m
|
||||
CONFIG_BRIDGE_EBT_BROUTE=m
|
||||
CONFIG_BRIDGE_EBT_T_FILTER=m
|
||||
CONFIG_BRIDGE_EBT_T_NAT=m
|
||||
CONFIG_BRIDGE_EBT_ARP=m
|
||||
CONFIG_BRIDGE_EBT_IP=m
|
||||
CONFIG_BRIDGE_EBT_IP6=m
|
||||
CONFIG_IP_SCTP=m
|
||||
CONFIG_RDS=y
|
||||
CONFIG_L2TP=m
|
||||
CONFIG_L2TP_V3=y
|
||||
CONFIG_L2TP_IP=m
|
||||
CONFIG_L2TP_ETH=m
|
||||
CONFIG_BRIDGE=m
|
||||
CONFIG_VLAN_8021Q=m
|
||||
CONFIG_VLAN_8021Q_GVRP=y
|
||||
CONFIG_VLAN_8021Q_MVRP=y
|
||||
CONFIG_LLC2=m
|
||||
CONFIG_NET_SCHED=y
|
||||
CONFIG_NET_SCH_HTB=m
|
||||
CONFIG_NET_SCH_PRIO=m
|
||||
CONFIG_NET_SCH_SFQ=m
|
||||
CONFIG_NET_SCH_TBF=m
|
||||
CONFIG_NET_SCH_NETEM=m
|
||||
CONFIG_NET_SCH_INGRESS=m
|
||||
CONFIG_NET_CLS_BASIC=m
|
||||
CONFIG_NET_CLS_FW=m
|
||||
CONFIG_NET_CLS_U32=m
|
||||
CONFIG_NET_CLS_CGROUP=m
|
||||
CONFIG_NET_CLS_BPF=m
|
||||
CONFIG_NET_CLS_ACT=y
|
||||
CONFIG_NET_ACT_POLICE=m
|
||||
CONFIG_NET_ACT_GACT=m
|
||||
CONFIG_NET_ACT_MIRRED=m
|
||||
CONFIG_NET_ACT_NAT=m
|
||||
CONFIG_NET_ACT_BPF=m
|
||||
CONFIG_OPENVSWITCH=m
|
||||
CONFIG_VSOCKETS=m
|
||||
CONFIG_VIRTIO_VSOCKETS=m
|
||||
CONFIG_NETLINK_DIAG=y
|
||||
CONFIG_CGROUP_NET_PRIO=y
|
||||
CONFIG_BPF_STREAM_PARSER=y
|
||||
CONFIG_CAN=y
|
||||
CONFIG_BT=m
|
||||
CONFIG_BT_RFCOMM=m
|
||||
CONFIG_BT_RFCOMM_TTY=y
|
||||
CONFIG_BT_BNEP=m
|
||||
CONFIG_BT_BNEP_MC_FILTER=y
|
||||
CONFIG_BT_BNEP_PROTO_FILTER=y
|
||||
CONFIG_BT_HIDP=m
|
||||
CONFIG_BT_HCIBTUSB=m
|
||||
CONFIG_BT_HCIBTUSB_AUTOSUSPEND=y
|
||||
CONFIG_BT_HCIBTUSB_MTK=y
|
||||
CONFIG_BT_HCIUART=m
|
||||
CONFIG_BT_HCIUART_BCSP=y
|
||||
CONFIG_BT_HCIUART_ATH3K=y
|
||||
CONFIG_BT_HCIUART_INTEL=y
|
||||
CONFIG_BT_HCIUART_AG6XX=y
|
||||
CONFIG_BT_HCIBCM203X=m
|
||||
CONFIG_BT_HCIBPA10X=m
|
||||
CONFIG_BT_HCIBFUSB=m
|
||||
CONFIG_BT_HCIVHCI=m
|
||||
CONFIG_BT_MRVL=m
|
||||
CONFIG_BT_ATH3K=m
|
||||
CONFIG_BT_VIRTIO=m
|
||||
CONFIG_CFG80211=m
|
||||
CONFIG_CFG80211_WEXT=y
|
||||
CONFIG_MAC80211=m
|
||||
CONFIG_RFKILL=m
|
||||
CONFIG_RFKILL_INPUT=y
|
||||
# CONFIG_PCIEASPM is not set
|
||||
# CONFIG_VGA_ARB is not set
|
||||
CONFIG_PCI_HOST_GENERIC=y
|
||||
CONFIG_PCI_SW_SWITCHTEC=m
|
||||
CONFIG_UEVENT_HELPER=y
|
||||
CONFIG_DEVTMPFS=y
|
||||
CONFIG_DEVTMPFS_MOUNT=y
|
||||
CONFIG_FW_LOADER_COMPRESS=y
|
||||
CONFIG_FW_LOADER_COMPRESS_ZSTD=y
|
||||
CONFIG_EFI_ZBOOT=y
|
||||
CONFIG_EFI_BOOTLOADER_CONTROL=m
|
||||
CONFIG_EFI_CAPSULE_LOADER=m
|
||||
CONFIG_EFI_TEST=m
|
||||
# CONFIG_EFI_DISABLE_RUNTIME is not set
|
||||
CONFIG_MTD=y
|
||||
CONFIG_MTD_CMDLINE_PARTS=y
|
||||
CONFIG_MTD_BLOCK=y
|
||||
CONFIG_MTD_BLOCK2MTD=y
|
||||
CONFIG_MTD_RAW_NAND=y
|
||||
# CONFIG_MTD_NAND_ECC_SW_HAMMING is not set
|
||||
CONFIG_MTD_SPI_NOR=y
|
||||
CONFIG_BLK_DEV_LOOP=y
|
||||
CONFIG_BLK_DEV_RAM=y
|
||||
CONFIG_BLK_DEV_RAM_SIZE=32768
|
||||
CONFIG_VIRTIO_BLK=y
|
||||
CONFIG_EEPROM_AT24=m
|
||||
CONFIG_BLK_DEV_SD=y
|
||||
# CONFIG_BLK_DEV_BSG is not set
|
||||
CONFIG_ATA=y
|
||||
CONFIG_SATA_AHCI=y
|
||||
CONFIG_AHCI_DWC=y
|
||||
CONFIG_NETDEVICES=y
|
||||
CONFIG_BONDING=m
|
||||
CONFIG_DUMMY=y
|
||||
CONFIG_WIREGUARD=m
|
||||
CONFIG_MACVLAN=m
|
||||
CONFIG_MACVTAP=m
|
||||
CONFIG_IPVLAN=m
|
||||
CONFIG_VXLAN=y
|
||||
CONFIG_TUN=m
|
||||
CONFIG_VETH=m
|
||||
CONFIG_VIRTIO_NET=m
|
||||
# CONFIG_NET_VENDOR_3COM is not set
|
||||
# CONFIG_NET_VENDOR_ADAPTEC is not set
|
||||
# CONFIG_NET_VENDOR_AGERE is not set
|
||||
# CONFIG_NET_VENDOR_ALACRITECH is not set
|
||||
# CONFIG_NET_VENDOR_ALTEON is not set
|
||||
# CONFIG_NET_VENDOR_AMAZON is not set
|
||||
# CONFIG_NET_VENDOR_AMD is not set
|
||||
# CONFIG_NET_VENDOR_AQUANTIA is not set
|
||||
# CONFIG_NET_VENDOR_ARC is not set
|
||||
# CONFIG_NET_VENDOR_ASIX is not set
|
||||
# CONFIG_NET_VENDOR_ATHEROS is not set
|
||||
# CONFIG_NET_VENDOR_BROADCOM is not set
|
||||
# CONFIG_NET_VENDOR_CADENCE is not set
|
||||
# CONFIG_NET_VENDOR_CAVIUM is not set
|
||||
# CONFIG_NET_VENDOR_CHELSIO is not set
|
||||
# CONFIG_NET_VENDOR_CISCO is not set
|
||||
# CONFIG_NET_VENDOR_CORTINA is not set
|
||||
# CONFIG_NET_VENDOR_DAVICOM is not set
|
||||
# CONFIG_NET_VENDOR_DEC is not set
|
||||
# CONFIG_NET_VENDOR_DLINK is not set
|
||||
# CONFIG_NET_VENDOR_EMULEX is not set
|
||||
# CONFIG_NET_VENDOR_ENGLEDER is not set
|
||||
# CONFIG_NET_VENDOR_EZCHIP is not set
|
||||
# CONFIG_NET_VENDOR_FUNGIBLE is not set
|
||||
# CONFIG_NET_VENDOR_GOOGLE is not set
|
||||
# CONFIG_NET_VENDOR_HUAWEI is not set
|
||||
# CONFIG_NET_VENDOR_INTEL is not set
|
||||
# CONFIG_NET_VENDOR_ADI is not set
|
||||
# CONFIG_NET_VENDOR_LITEX is not set
|
||||
# CONFIG_NET_VENDOR_MARVELL is not set
|
||||
# CONFIG_NET_VENDOR_MELLANOX is not set
|
||||
# CONFIG_NET_VENDOR_META is not set
|
||||
# CONFIG_NET_VENDOR_MICREL is not set
|
||||
# CONFIG_NET_VENDOR_MICROCHIP is not set
|
||||
# CONFIG_NET_VENDOR_MICROSEMI is not set
|
||||
# CONFIG_NET_VENDOR_MICROSOFT is not set
|
||||
# CONFIG_NET_VENDOR_MYRI is not set
|
||||
# CONFIG_NET_VENDOR_NI is not set
|
||||
# CONFIG_NET_VENDOR_NATSEMI is not set
|
||||
# CONFIG_NET_VENDOR_NETERION is not set
|
||||
# CONFIG_NET_VENDOR_NETRONOME is not set
|
||||
# CONFIG_NET_VENDOR_NVIDIA is not set
|
||||
# CONFIG_NET_VENDOR_OKI is not set
|
||||
# CONFIG_NET_VENDOR_PENSANDO is not set
|
||||
# CONFIG_NET_VENDOR_QLOGIC is not set
|
||||
# CONFIG_NET_VENDOR_BROCADE is not set
|
||||
# CONFIG_NET_VENDOR_QUALCOMM is not set
|
||||
# CONFIG_NET_VENDOR_RDC is not set
|
||||
# CONFIG_NET_VENDOR_REALTEK is not set
|
||||
# CONFIG_NET_VENDOR_RENESAS is not set
|
||||
# CONFIG_NET_VENDOR_ROCKER is not set
|
||||
# CONFIG_NET_VENDOR_SAMSUNG is not set
|
||||
# CONFIG_NET_VENDOR_SEEQ is not set
|
||||
# CONFIG_NET_VENDOR_SILAN is not set
|
||||
# CONFIG_NET_VENDOR_SIS is not set
|
||||
# CONFIG_NET_VENDOR_SOLARFLARE is not set
|
||||
# CONFIG_NET_VENDOR_SMSC is not set
|
||||
# CONFIG_NET_VENDOR_SOCIONEXT is not set
|
||||
CONFIG_STMMAC_ETH=y
|
||||
# CONFIG_DWMAC_LOONGSON is not set
|
||||
# CONFIG_NET_VENDOR_SUN is not set
|
||||
# CONFIG_NET_VENDOR_SYNOPSYS is not set
|
||||
# CONFIG_NET_VENDOR_TEHUTI is not set
|
||||
# CONFIG_NET_VENDOR_TI is not set
|
||||
# CONFIG_NET_VENDOR_VERTEXCOM is not set
|
||||
# CONFIG_NET_VENDOR_VIA is not set
|
||||
# CONFIG_NET_VENDOR_WANGXUN is not set
|
||||
# CONFIG_NET_VENDOR_WIZNET is not set
|
||||
# CONFIG_NET_VENDOR_XILINX is not set
|
||||
CONFIG_MOTORCOMM_PHY=y
|
||||
CONFIG_REALTEK_PHY=m
|
||||
CONFIG_CAN_SJA1000=y
|
||||
CONFIG_CAN_SJA1000_PLATFORM=y
|
||||
CONFIG_CAN_LSCANFD=y
|
||||
CONFIG_CAN_LSCANFD_PLATFORM=y
|
||||
CONFIG_PPP=m
|
||||
CONFIG_PPP_BSDCOMP=m
|
||||
CONFIG_PPP_DEFLATE=m
|
||||
CONFIG_PPP_FILTER=y
|
||||
CONFIG_PPP_MPPE=m
|
||||
CONFIG_PPP_MULTILINK=y
|
||||
CONFIG_PPPOE=m
|
||||
CONFIG_PPTP=m
|
||||
CONFIG_PPPOL2TP=m
|
||||
CONFIG_PPP_ASYNC=m
|
||||
CONFIG_PPP_SYNC_TTY=m
|
||||
CONFIG_USB_RTL8150=m
|
||||
CONFIG_USB_RTL8152=m
|
||||
# CONFIG_WLAN_VENDOR_ADMTEK is not set
|
||||
# CONFIG_WLAN_VENDOR_ATH is not set
|
||||
# CONFIG_WLAN_VENDOR_ATMEL is not set
|
||||
# CONFIG_WLAN_VENDOR_BROADCOM is not set
|
||||
# CONFIG_WLAN_VENDOR_INTEL is not set
|
||||
# CONFIG_WLAN_VENDOR_INTERSIL is not set
|
||||
# CONFIG_WLAN_VENDOR_MARVELL is not set
|
||||
# CONFIG_WLAN_VENDOR_MEDIATEK is not set
|
||||
# CONFIG_WLAN_VENDOR_MICROCHIP is not set
|
||||
# CONFIG_WLAN_VENDOR_PURELIFI is not set
|
||||
CONFIG_RT2X00=m
|
||||
CONFIG_RT2800USB=m
|
||||
# CONFIG_RT2800USB_RT33XX is not set
|
||||
# CONFIG_RT2800USB_RT35XX is not set
|
||||
CONFIG_RTL8187=m
|
||||
CONFIG_RTL8192CE=m
|
||||
CONFIG_RTL8192SE=m
|
||||
CONFIG_RTL8192DE=m
|
||||
CONFIG_RTL8723AE=m
|
||||
CONFIG_RTL8723BE=m
|
||||
CONFIG_RTL8188EE=m
|
||||
CONFIG_RTL8192EE=m
|
||||
CONFIG_RTL8821AE=m
|
||||
CONFIG_RTL8192CU=m
|
||||
# CONFIG_RTLWIFI_DEBUG is not set
|
||||
CONFIG_RTL8XXXU=m
|
||||
CONFIG_RTW88=m
|
||||
CONFIG_RTW88_8822BU=m
|
||||
CONFIG_RTW88_8822CU=m
|
||||
CONFIG_RTW88_8723DU=m
|
||||
CONFIG_RTW88_8821CU=m
|
||||
# CONFIG_WLAN_VENDOR_RSI is not set
|
||||
# CONFIG_WLAN_VENDOR_SILABS is not set
|
||||
# CONFIG_WLAN_VENDOR_ST is not set
|
||||
# CONFIG_WLAN_VENDOR_TI is not set
|
||||
# CONFIG_WLAN_VENDOR_ZYDAS is not set
|
||||
# CONFIG_WLAN_VENDOR_QUANTENNA is not set
|
||||
CONFIG_INPUT_SPARSEKMAP=y
|
||||
CONFIG_INPUT_MOUSEDEV=y
|
||||
CONFIG_INPUT_MOUSEDEV_PSAUX=y
|
||||
CONFIG_INPUT_EVDEV=y
|
||||
# CONFIG_KEYBOARD_ATKBD is not set
|
||||
CONFIG_KEYBOARD_XTKBD=m
|
||||
# CONFIG_MOUSE_PS2 is not set
|
||||
CONFIG_MOUSE_SERIAL=m
|
||||
CONFIG_INPUT_TOUCHSCREEN=y
|
||||
CONFIG_TOUCHSCREEN_GOODIX=y
|
||||
CONFIG_INPUT_MISC=y
|
||||
CONFIG_INPUT_UINPUT=m
|
||||
CONFIG_SERIO=m
|
||||
CONFIG_SERIO_LIBPS2=m
|
||||
CONFIG_SERIO_RAW=m
|
||||
CONFIG_LEGACY_PTY_COUNT=16
|
||||
CONFIG_SERIAL_8250=y
|
||||
CONFIG_SERIAL_8250_CONSOLE=y
|
||||
CONFIG_SERIAL_8250_NR_UARTS=16
|
||||
CONFIG_SERIAL_8250_RUNTIME_UARTS=16
|
||||
CONFIG_SERIAL_8250_EXTENDED=y
|
||||
CONFIG_SERIAL_8250_MANY_PORTS=y
|
||||
CONFIG_SERIAL_8250_SHARE_IRQ=y
|
||||
CONFIG_SERIAL_8250_RSA=y
|
||||
# CONFIG_SERIAL_8250_PERICOM is not set
|
||||
CONFIG_SERIAL_OF_PLATFORM=y
|
||||
CONFIG_SERIAL_NONSTANDARD=y
|
||||
CONFIG_VIRTIO_CONSOLE=y
|
||||
CONFIG_IPMI_HANDLER=m
|
||||
CONFIG_IPMI_DEVICE_INTERFACE=m
|
||||
CONFIG_IPMI_SI=m
|
||||
CONFIG_HW_RANDOM=y
|
||||
CONFIG_HW_RANDOM_VIRTIO=m
|
||||
# CONFIG_ACPI_I2C_OPREGION is not set
|
||||
CONFIG_I2C_CHARDEV=y
|
||||
CONFIG_I2C_GPIO=y
|
||||
CONFIG_I2C_LS2X=y
|
||||
CONFIG_SPI=y
|
||||
CONFIG_SPI_LOONGSON_PLATFORM=y
|
||||
CONFIG_PINCTRL=y
|
||||
CONFIG_PINCTRL_LOONGSON2=y
|
||||
CONFIG_PINCTRL_SINGLE=y
|
||||
CONFIG_GPIO_SYSFS=y
|
||||
CONFIG_GPIO_LOONGSON_IRQCHIP=y
|
||||
CONFIG_GPIO_LOONGSON_64BIT=y
|
||||
CONFIG_GPIO_PCA953X=y
|
||||
CONFIG_GPIO_PCA953X_IRQ=y
|
||||
CONFIG_POWER_RESET=y
|
||||
CONFIG_POWER_RESET_RESTART=y
|
||||
CONFIG_POWER_RESET_SYSCON=y
|
||||
CONFIG_POWER_RESET_SYSCON_POWEROFF=y
|
||||
CONFIG_SYSCON_REBOOT_MODE=y
|
||||
CONFIG_SENSORS_W83795=m
|
||||
CONFIG_SENSORS_W83627HF=m
|
||||
CONFIG_THERMAL=y
|
||||
CONFIG_LOONGSON2_THERMAL=y
|
||||
# CONFIG_MEDIA_CEC_SUPPORT is not set
|
||||
CONFIG_MEDIA_SUPPORT=y
|
||||
# CONFIG_DVB_CORE is not set
|
||||
CONFIG_MEDIA_USB_SUPPORT=y
|
||||
CONFIG_USB_VIDEO_CLASS=y
|
||||
# CONFIG_RADIO_ADAPTERS is not set
|
||||
# CONFIG_MEDIA_TUNER_E4000 is not set
|
||||
# CONFIG_MEDIA_TUNER_FC0011 is not set
|
||||
# CONFIG_MEDIA_TUNER_FC0012 is not set
|
||||
# CONFIG_MEDIA_TUNER_FC0013 is not set
|
||||
# CONFIG_MEDIA_TUNER_FC2580 is not set
|
||||
# CONFIG_MEDIA_TUNER_IT913X is not set
|
||||
# CONFIG_MEDIA_TUNER_M88RS6000T is not set
|
||||
# CONFIG_MEDIA_TUNER_MAX2165 is not set
|
||||
# CONFIG_MEDIA_TUNER_MC44S803 is not set
|
||||
# CONFIG_MEDIA_TUNER_MSI001 is not set
|
||||
# CONFIG_MEDIA_TUNER_MT2060 is not set
|
||||
# CONFIG_MEDIA_TUNER_MT2063 is not set
|
||||
# CONFIG_MEDIA_TUNER_MT20XX is not set
|
||||
# CONFIG_MEDIA_TUNER_MT2131 is not set
|
||||
# CONFIG_MEDIA_TUNER_MT2266 is not set
|
||||
# CONFIG_MEDIA_TUNER_MXL301RF is not set
|
||||
# CONFIG_MEDIA_TUNER_MXL5005S is not set
|
||||
# CONFIG_MEDIA_TUNER_MXL5007T is not set
|
||||
# CONFIG_MEDIA_TUNER_QM1D1B0004 is not set
|
||||
# CONFIG_MEDIA_TUNER_QM1D1C0042 is not set
|
||||
# CONFIG_MEDIA_TUNER_QT1010 is not set
|
||||
# CONFIG_MEDIA_TUNER_R820T is not set
|
||||
# CONFIG_MEDIA_TUNER_SI2157 is not set
|
||||
# CONFIG_MEDIA_TUNER_SIMPLE is not set
|
||||
# CONFIG_MEDIA_TUNER_TDA18212 is not set
|
||||
# CONFIG_MEDIA_TUNER_TDA18218 is not set
|
||||
# CONFIG_MEDIA_TUNER_TDA18250 is not set
|
||||
# CONFIG_MEDIA_TUNER_TDA18271 is not set
|
||||
# CONFIG_MEDIA_TUNER_TDA827X is not set
|
||||
# CONFIG_MEDIA_TUNER_TDA8290 is not set
|
||||
# CONFIG_MEDIA_TUNER_TDA9887 is not set
|
||||
# CONFIG_MEDIA_TUNER_TEA5761 is not set
|
||||
# CONFIG_MEDIA_TUNER_TEA5767 is not set
|
||||
# CONFIG_MEDIA_TUNER_TUA9001 is not set
|
||||
# CONFIG_MEDIA_TUNER_XC2028 is not set
|
||||
# CONFIG_MEDIA_TUNER_XC4000 is not set
|
||||
# CONFIG_MEDIA_TUNER_XC5000 is not set
|
||||
CONFIG_DRM=y
|
||||
CONFIG_DRM_PANEL_LVDS=y
|
||||
CONFIG_DRM_DISPLAY_CONNECTOR=y
|
||||
CONFIG_DRM_SIMPLE_BRIDGE=y
|
||||
CONFIG_DRM_LOONGSON=y
|
||||
CONFIG_DRM_SIMPLEDRM=y
|
||||
CONFIG_FB=y
|
||||
CONFIG_FB_EFI=y
|
||||
CONFIG_FB_MODE_HELPERS=y
|
||||
CONFIG_LCD_CLASS_DEVICE=y
|
||||
CONFIG_LCD_PLATFORM=y
|
||||
CONFIG_BACKLIGHT_CLASS_DEVICE=y
|
||||
CONFIG_BACKLIGHT_GPIO=y
|
||||
CONFIG_BACKLIGHT_LED=y
|
||||
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
|
||||
CONFIG_LOGO=y
|
||||
CONFIG_SOUND=y
|
||||
CONFIG_SND=y
|
||||
CONFIG_SND_SEQUENCER=m
|
||||
CONFIG_SND_SEQ_DUMMY=m
|
||||
CONFIG_SND_BT87X=m
|
||||
CONFIG_SND_BT87X_OVERCLOCK=y
|
||||
CONFIG_SND_HDA_INTEL=y
|
||||
CONFIG_SND_HDA_HWDEP=y
|
||||
CONFIG_SND_HDA_INPUT_BEEP=y
|
||||
CONFIG_SND_HDA_PATCH_LOADER=y
|
||||
CONFIG_SND_HDA_CODEC_REALTEK=y
|
||||
CONFIG_SND_HDA_CODEC_SIGMATEL=y
|
||||
CONFIG_SND_HDA_CODEC_HDMI=y
|
||||
CONFIG_SND_HDA_CODEC_CONEXANT=y
|
||||
CONFIG_SND_USB_AUDIO=m
|
||||
CONFIG_SND_SOC=y
|
||||
CONFIG_SND_SOC_LOONGSON=y
|
||||
CONFIG_SND_LS=y
|
||||
CONFIG_SND_LS_PCM=y
|
||||
CONFIG_SND_LS_PCM_GENERIC_DMA=y
|
||||
CONFIG_SND_SOC_ES8328_I2C=y
|
||||
CONFIG_SND_VIRTIO=m
|
||||
CONFIG_HIDRAW=y
|
||||
CONFIG_UHID=m
|
||||
CONFIG_HID_A4TECH=m
|
||||
CONFIG_HID_CHERRY=m
|
||||
CONFIG_HID_LOGITECH=m
|
||||
CONFIG_HID_LOGITECH_DJ=m
|
||||
CONFIG_LOGITECH_FF=y
|
||||
CONFIG_LOGIRUMBLEPAD2_FF=y
|
||||
CONFIG_LOGIG940_FF=y
|
||||
CONFIG_HID_MICROSOFT=m
|
||||
CONFIG_HID_MULTITOUCH=m
|
||||
CONFIG_HID_SUNPLUS=m
|
||||
CONFIG_USB_HIDDEV=y
|
||||
CONFIG_USB=y
|
||||
# CONFIG_USB_PCI is not set
|
||||
CONFIG_USB_OTG=y
|
||||
CONFIG_USB_MON=y
|
||||
CONFIG_USB_EHCI_HCD=y
|
||||
CONFIG_USB_EHCI_ROOT_HUB_TT=y
|
||||
CONFIG_USB_EHCI_HCD_PLATFORM=y
|
||||
CONFIG_USB_OHCI_HCD=y
|
||||
CONFIG_USB_OHCI_HCD_PLATFORM=y
|
||||
CONFIG_USB_ACM=m
|
||||
CONFIG_USB_PRINTER=m
|
||||
CONFIG_USB_STORAGE=y
|
||||
CONFIG_USB_UAS=y
|
||||
CONFIG_USB_DWC2=y
|
||||
CONFIG_USB_DWC2_HOST=y
|
||||
CONFIG_USB_SERIAL=m
|
||||
CONFIG_USB_SERIAL_CH341=m
|
||||
CONFIG_USB_SERIAL_CP210X=m
|
||||
CONFIG_USB_SERIAL_FTDI_SIO=m
|
||||
CONFIG_USB_SERIAL_PL2303=m
|
||||
CONFIG_USB_SERIAL_OPTION=m
|
||||
CONFIG_USB_GADGET=y
|
||||
CONFIG_TYPEC=m
|
||||
CONFIG_TYPEC_TCPM=m
|
||||
CONFIG_TYPEC_TCPCI=m
|
||||
CONFIG_TYPEC_UCSI=m
|
||||
CONFIG_UCSI_ACPI=m
|
||||
CONFIG_MMC=y
|
||||
# CONFIG_PWRSEQ_EMMC is not set
|
||||
CONFIG_MMC_LS2K=y
|
||||
CONFIG_LEDS_GPIO=y
|
||||
CONFIG_LEDS_PWM=y
|
||||
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
|
||||
CONFIG_RTC_CLASS=y
|
||||
CONFIG_RTC_DRV_DS1307=y
|
||||
CONFIG_RTC_DRV_EFI=y
|
||||
CONFIG_RTC_DRV_LOONGSON=y
|
||||
CONFIG_DMADEVICES=y
|
||||
CONFIG_LOONGSON2_APB_DMA=y
|
||||
CONFIG_LSIA_DMA=y
|
||||
CONFIG_UDMABUF=y
|
||||
CONFIG_DMABUF_HEAPS=y
|
||||
CONFIG_DMABUF_HEAPS_SYSTEM=y
|
||||
CONFIG_DMABUF_HEAPS_CMA=y
|
||||
CONFIG_UIO=y
|
||||
CONFIG_UIO_PDRV_GENIRQ=y
|
||||
CONFIG_UIO_DMEM_GENIRQ=y
|
||||
# CONFIG_VIRTIO_MENU is not set
|
||||
# CONFIG_VHOST_MENU is not set
|
||||
# CONFIG_LOONGARCH_PLATFORM_DEVICES is not set
|
||||
CONFIG_COMMON_CLK_LOONGSON2=y
|
||||
# CONFIG_COMMON_CLK_LOONGSON2X is not set
|
||||
CONFIG_IOMMU_DEBUGFS=y
|
||||
CONFIG_LOONGSON2_GUTS=y
|
||||
CONFIG_LOONGSON2_PM=y
|
||||
CONFIG_IIO=y
|
||||
CONFIG_LS_2K300_ADC=y
|
||||
CONFIG_PWM=y
|
||||
CONFIG_PWM_LOONGSON=y
|
||||
CONFIG_GENERIC_PHY=y
|
||||
CONFIG_EXT2_FS=y
|
||||
CONFIG_EXT2_FS_XATTR=y
|
||||
CONFIG_EXT2_FS_POSIX_ACL=y
|
||||
CONFIG_EXT2_FS_SECURITY=y
|
||||
CONFIG_EXT3_FS=y
|
||||
CONFIG_EXT3_FS_POSIX_ACL=y
|
||||
CONFIG_EXT3_FS_SECURITY=y
|
||||
CONFIG_EXPORTFS_BLOCK_OPS=y
|
||||
CONFIG_FANOTIFY=y
|
||||
CONFIG_FANOTIFY_ACCESS_PERMISSIONS=y
|
||||
CONFIG_QUOTA=y
|
||||
CONFIG_AUTOFS_FS=y
|
||||
CONFIG_OVERLAY_FS=y
|
||||
CONFIG_OVERLAY_FS_INDEX=y
|
||||
CONFIG_OVERLAY_FS_XINO_AUTO=y
|
||||
CONFIG_OVERLAY_FS_METACOPY=y
|
||||
CONFIG_ISO9660_FS=y
|
||||
CONFIG_JOLIET=y
|
||||
CONFIG_ZISOFS=y
|
||||
CONFIG_MSDOS_FS=y
|
||||
CONFIG_VFAT_FS=y
|
||||
CONFIG_FAT_DEFAULT_CODEPAGE=936
|
||||
CONFIG_FAT_DEFAULT_IOCHARSET="gb2312"
|
||||
CONFIG_EXFAT_FS=y
|
||||
CONFIG_NTFS3_FS=y
|
||||
CONFIG_NTFS3_64BIT_CLUSTER=y
|
||||
CONFIG_NTFS3_LZX_XPRESS=y
|
||||
CONFIG_PROC_KCORE=y
|
||||
CONFIG_TMPFS=y
|
||||
CONFIG_TMPFS_POSIX_ACL=y
|
||||
CONFIG_HUGETLBFS=y
|
||||
CONFIG_CONFIGFS_FS=y
|
||||
# CONFIG_MISC_FILESYSTEMS is not set
|
||||
CONFIG_NFS_FS=y
|
||||
CONFIG_NFS_V3_ACL=y
|
||||
CONFIG_NFS_V4=y
|
||||
CONFIG_NFS_V4_1=y
|
||||
CONFIG_NFS_V4_2=y
|
||||
CONFIG_ROOT_NFS=y
|
||||
# CONFIG_NFS_DISABLE_UDP_SUPPORT is not set
|
||||
CONFIG_NLS_CODEPAGE_936=y
|
||||
CONFIG_NLS_ASCII=y
|
||||
CONFIG_NLS_UTF8=y
|
||||
CONFIG_KEY_DH_OPERATIONS=y
|
||||
CONFIG_SECURITY=y
|
||||
CONFIG_SECURITY_SELINUX=y
|
||||
CONFIG_SECURITY_SELINUX_BOOTPARAM=y
|
||||
CONFIG_SECURITY_APPARMOR=y
|
||||
CONFIG_SECURITY_YAMA=y
|
||||
CONFIG_DEFAULT_SECURITY_DAC=y
|
||||
CONFIG_CRYPTO_USER=m
|
||||
# CONFIG_CRYPTO_MANAGER_DISABLE_TESTS is not set
|
||||
CONFIG_CRYPTO_CRYPTD=m
|
||||
CONFIG_CRYPTO_ANUBIS=m
|
||||
CONFIG_CRYPTO_BLOWFISH=m
|
||||
CONFIG_CRYPTO_CAST5=m
|
||||
CONFIG_CRYPTO_CAST6=m
|
||||
CONFIG_CRYPTO_KHAZAD=m
|
||||
CONFIG_CRYPTO_SEED=m
|
||||
CONFIG_CRYPTO_SERPENT=m
|
||||
CONFIG_CRYPTO_TEA=m
|
||||
CONFIG_CRYPTO_TWOFISH=m
|
||||
CONFIG_CRYPTO_CHACHA20POLY1305=m
|
||||
CONFIG_CRYPTO_ESSIV=m
|
||||
CONFIG_CRYPTO_BLAKE2B=m
|
||||
CONFIG_CRYPTO_VMAC=m
|
||||
CONFIG_CRYPTO_WP512=m
|
||||
CONFIG_CRYPTO_XXHASH=y
|
||||
CONFIG_CRYPTO_CRC32=m
|
||||
CONFIG_CRYPTO_LZO=m
|
||||
CONFIG_CRYPTO_842=m
|
||||
CONFIG_CRYPTO_LZ4=m
|
||||
CONFIG_CRYPTO_LZ4HC=m
|
||||
CONFIG_CRYPTO_USER_API_HASH=m
|
||||
CONFIG_CRYPTO_USER_API_SKCIPHER=m
|
||||
CONFIG_CRYPTO_USER_API_RNG=m
|
||||
CONFIG_CRYPTO_USER_API_AEAD=m
|
||||
CONFIG_CRYPTO_DEV_VIRTIO=m
|
||||
CONFIG_CRC_ITU_T=m
|
||||
# CONFIG_XZ_DEC_POWERPC is not set
|
||||
# CONFIG_XZ_DEC_SPARC is not set
|
||||
CONFIG_DMA_CMA=y
|
||||
CONFIG_CMA_SIZE_MBYTES=0
|
||||
CONFIG_IRQ_POLL=y
|
||||
CONFIG_PRINTK_TIME=y
|
||||
CONFIG_DYNAMIC_DEBUG=y
|
||||
CONFIG_STRIP_ASM_SYMS=y
|
||||
CONFIG_MAGIC_SYSRQ=y
|
||||
CONFIG_DEBUG_FS=y
|
||||
# CONFIG_SCHED_DEBUG is not set
|
||||
CONFIG_SCHEDSTATS=y
|
||||
# CONFIG_FTRACE is not set
|
||||
CONFIG_UNWINDER_ORC=y
|
||||
@@ -4064,7 +4064,14 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
|
||||
*/
|
||||
rtl8xxxu_write16(priv, REG_TRXFF_BNDY + 2, fops->trxff_boundary);
|
||||
|
||||
ret = rtl8xxxu_download_firmware(priv);
|
||||
// OTG port will cause download firmware fail(especiall in alpine), try again
|
||||
for (int retry = 0; retry < 10; retry++)
|
||||
{
|
||||
udelay(10);
|
||||
ret = rtl8xxxu_download_firmware(priv);
|
||||
if (ret == 0)
|
||||
break;
|
||||
}
|
||||
dev_dbg(dev, "%s: download_firmware %i\n", __func__, ret);
|
||||
if (ret)
|
||||
goto exit;
|
||||
|
||||
Reference in New Issue
Block a user