According to the chip manual, the I2C register access type of
Loongson-2K2000/LS7A is "B", so we can only access registers in byte
form (readb()/writeb()).
Although Loongson-2K0500/Loongson-2K1000 do not have similar
constraints, register accesses in byte form also behave correctly.
Also, in hardware, the frequency division registers are defined as two
separate registers (high 8-bit and low 8-bit), so we just access them
directly as bytes.
Cc: stable@vger.kernel.org
Fixes: 015e61f0bffd ("i2c: ls2x: Add driver for Loongson-2K/LS7A I2C controller")
Co-developed-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The size of DMA descriptors is 32 bytes at most.
net_prefetch() for received frames, and keep prefetch() for descriptors.
This patch brings ~4.8% driver performance improvement in a TCP RX
throughput test with iPerf tool on a single isolated Cortex-A65 CPU
core, 2.92 Gbits/sec increased to 3.06 Gbits/sec.
Suggested-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Current code prefetches cache lines for the received frame first, and
then dma_sync_single_for_cpu() against this frame, this is wrong.
Cache prefetch should be triggered after dma_sync_single_for_cpu().
This patch brings ~2.8% driver performance improvement in a TCP RX
throughput test with iPerf tool on a single isolated Cortex-A65 CPU
core, 2.84 Gbits/sec increased to 2.92 Gbits/sec.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The enable_gpe_wakeup() function calls acpi_enable_all_wakeup_gpes(),
and the later one may call the preempt_schedule_common() function,
resulting in a thread switch and causing the CPU to be in an interrupt
enabled state after the enable_gpe_wakeup() function returns, leading
to the warnings as follow.
[ C0] WARNING: ... at kernel/time/timekeeping.c:845 ktime_get+0xbc/0xc8
[ C0] ...
[ C0] Call Trace:
[ C0] [<90000000002243b4>] show_stack+0x64/0x188
[ C0] [<900000000164673c>] dump_stack_lvl+0x60/0x88
[ C0] [<90000000002687e4>] __warn+0x8c/0x148
[ C0] [<90000000015e9978>] report_bug+0x1c0/0x2b0
[ C0] [<90000000016478e4>] do_bp+0x204/0x3b8
[ C0] [<90000000025b1924>] exception_handlers+0x1924/0x10000
[ C0] [<9000000000343bbc>] ktime_get+0xbc/0xc8
[ C0] [<9000000000354c08>] tick_sched_timer+0x30/0xb0
[ C0] [<90000000003408e0>] __hrtimer_run_queues+0x160/0x378
[ C0] [<9000000000341f14>] hrtimer_interrupt+0x144/0x388
[ C0] [<9000000000228348>] constant_timer_interrupt+0x38/0x48
[ C0] [<90000000002feba4>] __handle_irq_event_percpu+0x64/0x1e8
[ C0] [<90000000002fed48>] handle_irq_event_percpu+0x20/0x80
[ C0] [<9000000000306b9c>] handle_percpu_irq+0x5c/0x98
[ C0] [<90000000002fd4a0>] generic_handle_domain_irq+0x30/0x48
[ C0] [<9000000000d0c7b0>] handle_cpu_irq+0x70/0xa8
[ C0] [<9000000001646b30>] handle_loongarch_irq+0x30/0x48
[ C0] [<9000000001646bc8>] do_vint+0x80/0xe0
[ C0] [<90000000002aea1c>] finish_task_switch.isra.0+0x8c/0x2a8
[ C0] [<900000000164e34c>] __schedule+0x314/0xa48
[ C0] [<900000000164ead8>] schedule+0x58/0xf0
[ C0] [<9000000000294a2c>] worker_thread+0x224/0x498
[ C0] [<900000000029d2f0>] kthread+0xf8/0x108
[ C0] [<9000000000221f28>] ret_from_kernel_thread+0xc/0xa4
[ C0]
[ C0] ---[ end trace 0000000000000000 ]---
The root cause is acpi_enable_all_wakeup_gpes() uses a mutex to protect
acpi_hw_enable_all_wakeup_gpes(), and acpi_ut_acquire_mutex() may cause
a thread switch. Since there is no longer concurrent execution during
loongarch_acpi_suspend(), we can call acpi_hw_enable_all_wakeup_gpes()
directly in enable_gpe_wakeup().
The solution is similar to commit 22db06337f590d01 ("ACPI: sleep: Avoid
breaking S3 wakeup due to might_sleep()").
Fixes: 366bb35a8e48 ("LoongArch: Add suspend (ACPI S3) support")
Signed-off-by: Qunqin Zhao <zhaoqunqin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
avecintc_init() enables the Advanced Interrupt Controller (AVEC) of
the boot CPU node, but nothing enables the AVEC on secondary nodes.
Move the enablement to the CPU hotplug callback so that secondary nodes get
the AVEC enabled too. In theory enabling it once per node would be
sufficient, but redundant enabling does no hurt, so keep the code simple
and do it unconditionally.
Signed-off-by: Tianyang Zhang <zhangtianyang@loongson.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/all/20250111023704.17285-1-zhangtianyang@loongson.cn
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Since commit 02fb4f008433 ("clk: clk-loongson2: Fix potential buffer
overflow in flexible-array member access"), the clk provider register is
failed.
The count of `clks_num` is shown below:
for (p = data; p->name; p++)
clks_num++;
In fact, `clks_num` represents the number of SoC clocks and should be
expressed as the maximum value of the clock binding id in use (p->id + 1).
Now we fix it to avoid the following error when trying to register a clk
provider:
[ 13.409595] of_clk_hw_onecell_get: invalid index 17
Cc: stable@vger.kernel.org
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Fixes: 02fb4f008433 ("clk: clk-loongson2: Fix potential buffer overflow in flexible-array member access")
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://lore.kernel.org/r/82e43d89a9a6791129cf8ea14f4eeb666cd87be4.1736856470.git.zhoubinbin@loongson.cn
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The TOY_MATCH0_REG should be cleared to 0 in the RTC interrupt handler,
otherwise the interrupt cannot be cleared, which will cause the
loongson_rtc_isr() to be triggered multiple times.
The previous code cleared TOY_MATCH0_REG in the loongson_rtc_handler(),
which is an ACPI interrupt. This did not prevent loongson_rtc_isr()
from being triggered multiple times.
This commit moves the clearing of TOY_MATCH0_REG to the
loongson_rtc_isr() to ensure that the interrupt is properly cleared.
Fixes: 1b733a9ebc3d ("rtc: Add rtc driver for the Loongson family chips")
Signed-off-by: Ming Wang <wangming01@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Keguang Zhang <keguang.zhang@gmail.com> # on LS1B
Tested-by: Keguang Zhang <keguang.zhang@gmail.com>
Link: https://lore.kernel.org/r/20241205114307.1891418-1-wangming01@loongson.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Alexandre observed a warning emitted from pci_msi_setup_msi_irqs() on a
RISCV platform which does not provide PCI/MSI support:
WARNING: CPU: 1 PID: 1 at drivers/pci/msi/msi.h:121 pci_msi_setup_msi_irqs+0x2c/0x32
__pci_enable_msix_range+0x30c/0x596
pci_msi_setup_msi_irqs+0x2c/0x32
pci_alloc_irq_vectors_affinity+0xb8/0xe2
RISCV uses hierarchical interrupt domains and correctly does not implement
the legacy fallback. The warning triggers from the legacy fallback stub.
That warning is bogus as the PCI/MSI layer knows whether a PCI/MSI parent
domain is associated with the device or not. There is a check for MSI-X,
which has a legacy assumption. But that legacy fallback assumption is only
valid when legacy support is enabled, but otherwise the check should simply
return -ENOTSUPP.
Loongarch tripped over the same problem and blindly enabled legacy support
without implementing the legacy fallbacks. There are weak implementations
which return an error, so the problem was papered over.
Correct pci_msi_domain_supports() to evaluate the legacy mode and add
the missing supported check into the MSI enable path to complete it.
Fixes: d2a463b29741 ("PCI/MSI: Reject multi-MSI early")
Reported-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/87ed2a8ow5.ffs@tglx
Signed-off-by: michael <michael5hzg@gmail.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Clang on LoongArch (18+) appears to be unaffected by the bug causing
excessive stack usage in calculate_bandwidth(). But when building DC_FP
support the stack frame size can be as large as 2816 bytes, which causes
the FRAME_WARN build warnings. So on LoongArch we allow building DC with
clang, but disable DC_FP by default.
The help message is also updated.
Tested-by: Rui Wang <wangrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: michael <michael5hzg@gmail.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Since ttm_bo_move_null() is exactly the same as ttm_resource_free() +
ttm_bo_assign_mem(), we use ttm_bo_move_null() for the GTT --> SYSTEM
move case too. Then the code is more consistent as the SYSTEM --> GTT
move case.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: michael <michael5hzg@gmail.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Flexible-array member `hws` in `struct clk_hw_onecell_data` is annotated
with the `counted_by()` attribute. This means that when memory is
allocated for this array, the _counter_, which in this case is member
`num` in the flexible structure, should be set to the maximum number of
elements the flexible array can contain, or fewer.
In this case, the total number of elements for the flexible array is
determined by variable `clks_num` when allocating heap space via
`devm_kzalloc()`, as shown below:
289 struct loongson2_clk_provider *clp;
...
296 for (p = data; p->name; p++)
297 clks_num++;
298
299 clp = devm_kzalloc(dev, struct_size(clp, clk_data.hws, clks_num),
300 GFP_KERNEL);
So, `clp->clk_data.num` should be set to `clks_num` or less, and not
exceed `clks_num`, as is currently the case. Otherwise, if data is
written into `clp->clk_data.hws[clks_num]`, the instrumentation
provided by the compiler won't detect the overflow, leading to a
memory corruption bug at runtime.
Fix this issue by setting `clp->clk_data.num` to `clks_num`.
Fixes: 9796ec0bd04b ("clk: clk-loongson2: Refactor driver for adding new platforms")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/ZzaN5MpmMr0hwHw9@kspp
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: michael <michael5hzg@gmail.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Some heap space is allocated for the flexible structure `struct
clk_hw_onecell_data` and its flexible-array member `hws` through
the composite structure `struct loongson2_clk_provider` in function
`loongson2_clk_probe()`, as shown below:
289 struct loongson2_clk_provider *clp;
...
296 for (p = data; p->name; p++)
297 clks_num++;
298
299 clp = devm_kzalloc(dev, struct_size(clp, clk_data.hws, clks_num),
300 GFP_KERNEL);
Then some data is written into the flexible array:
350 clp->clk_data.hws[p->id] = hw;
This corrupts `clk_lock`, which is the spinlock variable immediately
following the `clk_data` member in `struct loongson2_clk_provider`:
struct loongson2_clk_provider {
void __iomem *base;
struct device *dev;
struct clk_hw_onecell_data clk_data;
spinlock_t clk_lock; /* protect access to DIV registers */
};
The problem is that the flexible structure is currently placed in the
middle of `struct loongson2_clk_provider` instead of at the end.
Fix this by moving `struct clk_hw_onecell_data clk_data;` to the end of
`struct loongson2_clk_provider`. Also, add a code comment to help
prevent this from happening again in case new members are added to the
structure in the future.
This change also fixes the following -Wflex-array-member-not-at-end
warning:
drivers/clk/clk-loongson2.c:32:36: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Fixes: 9796ec0bd04b ("clk: clk-loongson2: Refactor driver for adding new platforms")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/ZzZ-cd_EFXs6qFaH@kspp
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: michael <michael5hzg@gmail.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
maoxiaochuan