The current max_pfn equals to zero. In this case, it causes user cannot
get some page information through /proc filesystem such as kpagecount.
The following message is displayed by stress-ng test suite with command
"stress-ng --verbose --physpage 1 -t 1".
# stress-ng --verbose --physpage 1 -t 1
stress-ng: error: [1691] physpage: cannot read page count for address 0x134ac000 in /proc/kpagecount, errno=22 (Invalid argument)
stress-ng: error: [1691] physpage: cannot read page count for address 0x7ffff207c3a8 in /proc/kpagecount, errno=22 (Invalid argument)
stress-ng: error: [1691] physpage: cannot read page count for address 0x134b0000 in /proc/kpagecount, errno=22 (Invalid argument)
...
After applying this patch, the kernel can pass the test.
# stress-ng --verbose --physpage 1 -t 1
stress-ng: debug: [1701] physpage: [1701] started (instance 0 on CPU 3)
stress-ng: debug: [1701] physpage: [1701] exited (instance 0 on CPU 3)
stress-ng: debug: [1700] physpage: [1701] terminated (success)
Cc: stable@vger.kernel.org # 6.8+
Fixes: ff6c3d81f2e8 ("NUMA: optimize detection of memory with no node id assigned by firmware")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
When compiling on LoongArch, there exists the following objtool warning
in arch/loongarch/kernel/machine_kexec.o:
kexec_reboot() falls through to next function crash_shutdown_secondary()
Avoid using unreachable() as it can (and will in the absence of UBSAN)
generate fall-through code. Use BUG() so we get a "break BRK_BUG" trap
(with unreachable annotation).
Cc: stable@vger.kernel.org # 6.12+
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
According to the chip manual, the I2C register access type of
Loongson-2K2000/LS7A is "B", so we can only access registers in byte
form (readb()/writeb()).
Although Loongson-2K0500/Loongson-2K1000 do not have similar
constraints, register accesses in byte form also behave correctly.
Also, in hardware, the frequency division registers are defined as two
separate registers (high 8-bit and low 8-bit), so we just access them
directly as bytes.
Cc: stable@vger.kernel.org
Fixes: 015e61f0bffd ("i2c: ls2x: Add driver for Loongson-2K/LS7A I2C controller")
Co-developed-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Glibc added support for .gnu.hash in 2006 and .hash has been obsoleted
far before the first LoongArch CPU was taped. Using --hash-style=sysv
might imply unaddressed issues and confuse readers.
Some architectures use an explicit --hash-style=both for vDSO here, but
DT_GNU_HASH has already been supported by Glibc and Musl and become the
de-facto standard of the distros when the first LoongArch CPU was taped.
So DT_HASH seems just wasting storage space for LoongArch.
Just drop the option and rely on the linker default, which is likely
"gnu" (Arch, Debian, Gentoo, LFS) on all LoongArch distros (confirmed on
Arch, Debian, Gentoo, and LFS; AOSC now defaults to "both" but it seems
just an oversight).
Following the logic of commit 48f6430505c0b049 ("arm64/vdso: Remove
--hash-style=sysv").
Link: https://github.com/AOSC-Dev/aosc-os-abbs/pull/9796
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Make use of the t8 register for vgetrandom-chacha, so we don't need to
reuse a register and rematerialize a constant. I
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
When CONFIG_RANDOM_KMALLOC_CACHES or other randomization infrastructrue
enabled, the idle_task's stack may different between the booting kernel
and target kernel. So when resuming from hibernation, an ACTION_BOOT_CPU
IPI wakeup the idle instruction in arch_cpu_idle_dead() and jump to the
interrupt handler. But since the stack pointer is changed, the interrupt
handler cannot restore correct context.
So rename the current arch_cpu_idle_dead() to idle_play_dead(), make it
as the default version of play_dead(), and the new arch_cpu_idle_dead()
call play_dead() directly. For hibernation, implement an arch-specific
hibernate_resume_nonboot_cpu_disable() to use the polling version (idle
instruction is replace by nop, and irq is disabled) of play_dead(), i.e.
poll_play_dead(), to avoid IPI handler corrupting the idle_task's stack
when resuming from hibernation.
This solution is a little similar to commit 406f992e4a372dafbe3c ("x86 /
hibernate: Use hlt_play_dead() when resuming from hibernation").
Cc: stable@vger.kernel.org
Tested-by: Erpeng Xu <xuerpeng@uniontech.com>
Tested-by: Yuli Wang <wangyuli@uniontech.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Option HAVE_VIRT_CPU_ACCOUNTING_GEN is selected by default for 64bit
system in kconfig file arch/Kconfig. There is another selection in file
arch/loongarch/Kconfig if SMP is not selected. Indeed this option is
SMP-safe so it brings out some misunderstanding for non-SMP case. Here
always select option HAVE_VIRT_CPU_ACCOUNTING_GEN for future possible
32bit system (it is also 32bit-safe because we no longer use cputime_t).
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The size of DMA descriptors is 32 bytes at most.
net_prefetch() for received frames, and keep prefetch() for descriptors.
This patch brings ~4.8% driver performance improvement in a TCP RX
throughput test with iPerf tool on a single isolated Cortex-A65 CPU
core, 2.92 Gbits/sec increased to 3.06 Gbits/sec.
Suggested-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Current code prefetches cache lines for the received frame first, and
then dma_sync_single_for_cpu() against this frame, this is wrong.
Cache prefetch should be triggered after dma_sync_single_for_cpu().
This patch brings ~2.8% driver performance improvement in a TCP RX
throughput test with iPerf tool on a single isolated Cortex-A65 CPU
core, 2.84 Gbits/sec increased to 2.92 Gbits/sec.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Commit 69e3a6aa6be2 ("LoongArch: Add checksum optimization for 64-bit
system") would cause an undefined shift and an out-of-bounds read.
Commit 8bd795fedb84 ("arm64: csum: Fix OoB access in IP checksum code
for negative lengths") fixes the same issue on ARM64.
Fixes: 69e3a6aa6be2 ("LoongArch: Add checksum optimization for 64-bit system")
Co-developed-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Yuli Wang <wangyuli@uniontech.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Now kernel_page_present() always return true for KPRANGE/XKPRANGE
addresses, this isn't correct because hibernation (ACPI S4) use it
to distinguish whether a page is saveable. If all KPRANGE/XKPRANGE
addresses are considered as saveable, then reserved memory such as
EFI_RUNTIME_SERVICES_CODE / EFI_RUNTIME_SERVICES_DATA will also be
saved and restored.
Fix this by returning true only if the KPRANGE/XKPRANGE address is in
memblock.memory.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
LoongArch re-enables interrupts on its idle routine and performs a
TIF_NEED_RESCHED check afterwards before putting the CPU to sleep.
The IRQs firing between the check and the idle instruction may set the
TIF_NEED_RESCHED flag. In order to deal with such a race, IRQs
interrupting __arch_cpu_idle() rollback their return address to the
beginning of __arch_cpu_idle() so that TIF_NEED_RESCHED is checked
again before going back to sleep.
However idle IRQs can also queue timers that may require a tick
reprogramming through a new generic idle loop iteration but those timers
would go unnoticed here because __arch_cpu_idle() only checks
TIF_NEED_RESCHED. It doesn't check for pending timers.
Fix this with fast-forwarding idle IRQs return address to the end of the
idle routine instead of the beginning, so that the generic idle loop can
handle both TIF_NEED_RESCHED and pending timers.
Fixes: 0603839b18f4 ("LoongArch: Add exception/interrupt handling")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The notifier hook mechanism in proc and cpuinfo is actually unnecessary
for LoongArch because it's not used anywhere.
It was originally added to the MIPS code in commit d6d3c9afaab4 ("MIPS:
MT: proc: Add support for printing VPE and TC ids"), and LoongArch then
inherited it.
But as the kernel code stands now, this notifier hook mechanism doesn't
really make sense for either LoongArch or MIPS.
In addition, the seq_file forward declaration needs to be moved to its
proper place, as only the show_ipi_list() function in smp.c requires it.
Co-developed-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Yuli Wang <wangyuli@uniontech.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The maximum number of load/store watchpoints and fetch instruction
watchpoints is 14 each according to LoongArch Reference Manual, so
extend the maximum number of watchpoints from 8 to 14 for ptrace.
By the way, just simply change 8 to 14 for the definition in struct
user_watch_state at the beginning, but it may corrupt uapi, then add
a new struct user_watch_state_v2 directly.
As far as I can tell, the only users for this struct in the userspace
are GDB and LLDB, there are no any problems of software compatibility
between the application and kernel according to the analysis.
The compatibility problem has been considered while developing and
testing. When the applications in the userspace get watchpoint state,
the length will be specified which is no bigger than the sizeof struct
user_watch_state or user_watch_state_v2, the actual length is assigned
as the minimal value of the application and kernel in the generic code
of ptrace:
kernel/ptrace.c: ptrace_regset():
kiov->iov_len = min(kiov->iov_len,
(__kernel_size_t) (regset->n * regset->size));
if (req == PTRACE_GETREGSET)
return copy_regset_to_user(task, view, regset_no, 0,
kiov->iov_len, kiov->iov_base);
else
return copy_regset_from_user(task, view, regset_no, 0,
kiov->iov_len, kiov->iov_base);
For example, there are four kind of combinations, all of them work well.
(1) "older kernel + older gdb", the actual length is 8+(8+8+4+4)*8=200;
(2) "newer kernel + newer gdb", the actual length is 8+(8+8+4+4)*14=344;
(3) "older kernel + newer gdb", the actual length is 8+(8+8+4+4)*8=200;
(4) "newer kernel + older gdb", the actual length is 8+(8+8+4+4)*8=200.
Link: https://loongson.github.io/LoongArch-Documentation/LoongArch-Vol1-EN.html#control-and-status-registers-related-to-watchpoints
Cc: stable@vger.kernel.org
Fixes: 1a69f7a161a7 ("LoongArch: ptrace: Expose hardware breakpoints to debuggers")
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The enable_gpe_wakeup() function calls acpi_enable_all_wakeup_gpes(),
and the later one may call the preempt_schedule_common() function,
resulting in a thread switch and causing the CPU to be in an interrupt
enabled state after the enable_gpe_wakeup() function returns, leading
to the warnings as follow.
[ C0] WARNING: ... at kernel/time/timekeeping.c:845 ktime_get+0xbc/0xc8
[ C0] ...
[ C0] Call Trace:
[ C0] [<90000000002243b4>] show_stack+0x64/0x188
[ C0] [<900000000164673c>] dump_stack_lvl+0x60/0x88
[ C0] [<90000000002687e4>] __warn+0x8c/0x148
[ C0] [<90000000015e9978>] report_bug+0x1c0/0x2b0
[ C0] [<90000000016478e4>] do_bp+0x204/0x3b8
[ C0] [<90000000025b1924>] exception_handlers+0x1924/0x10000
[ C0] [<9000000000343bbc>] ktime_get+0xbc/0xc8
[ C0] [<9000000000354c08>] tick_sched_timer+0x30/0xb0
[ C0] [<90000000003408e0>] __hrtimer_run_queues+0x160/0x378
[ C0] [<9000000000341f14>] hrtimer_interrupt+0x144/0x388
[ C0] [<9000000000228348>] constant_timer_interrupt+0x38/0x48
[ C0] [<90000000002feba4>] __handle_irq_event_percpu+0x64/0x1e8
[ C0] [<90000000002fed48>] handle_irq_event_percpu+0x20/0x80
[ C0] [<9000000000306b9c>] handle_percpu_irq+0x5c/0x98
[ C0] [<90000000002fd4a0>] generic_handle_domain_irq+0x30/0x48
[ C0] [<9000000000d0c7b0>] handle_cpu_irq+0x70/0xa8
[ C0] [<9000000001646b30>] handle_loongarch_irq+0x30/0x48
[ C0] [<9000000001646bc8>] do_vint+0x80/0xe0
[ C0] [<90000000002aea1c>] finish_task_switch.isra.0+0x8c/0x2a8
[ C0] [<900000000164e34c>] __schedule+0x314/0xa48
[ C0] [<900000000164ead8>] schedule+0x58/0xf0
[ C0] [<9000000000294a2c>] worker_thread+0x224/0x498
[ C0] [<900000000029d2f0>] kthread+0xf8/0x108
[ C0] [<9000000000221f28>] ret_from_kernel_thread+0xc/0xa4
[ C0]
[ C0] ---[ end trace 0000000000000000 ]---
The root cause is acpi_enable_all_wakeup_gpes() uses a mutex to protect
acpi_hw_enable_all_wakeup_gpes(), and acpi_ut_acquire_mutex() may cause
a thread switch. Since there is no longer concurrent execution during
loongarch_acpi_suspend(), we can call acpi_hw_enable_all_wakeup_gpes()
directly in enable_gpe_wakeup().
The solution is similar to commit 22db06337f590d01 ("ACPI: sleep: Avoid
breaking S3 wakeup due to might_sleep()").
Fixes: 366bb35a8e48 ("LoongArch: Add suspend (ACPI S3) support")
Signed-off-by: Qunqin Zhao <zhaoqunqin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
SETUP_SLEEP should only save the GPR context, which is symmetric to
SETUP_WAKEUP, so move the acpi_saved_sp handling out of SETUP_SLEEP.
Move "addi.d sp, sp, PT_SIZE" into SETUP_WAKEUP for the same reason.
No functional changes.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
1. Early return for user mode triggered exception with all types.
2. Give a chance to call fixup_exception() for default types (like
S390).
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Commit cca98e9f8b5ebcd964 ("mm: enforce that vmap can't map pages
executable") enforces the W^X protection by not allowing remapping
existing pages as executable. Add LoongArch bits so that LoongArch
can benefit the same protection.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
maoxiaochuan