struct tegra_bpmp::clocks is a pointer to a dynamically allocated array
of pointers to 'struct tegra_bpmp_clk'.
But the size of the allocated area is calculated like it is an array
containing actual 'struct tegra_bpmp_clk' objects - it's not true, there
are just pointers.
Found by Linux Verification Center (linuxtesting.org) with Svace static
analysis tool.
Fixes: 2db12b15c6f3 ("clk: tegra: Register clocks from root to leaf")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Init acpi_gbl_use_global_lock to false, in order to void error messages
during boot phase:
ACPI Error: Could not enable GlobalLock event (20240827/evxfevnt-182)
ACPI Error: No response from Global Lock hardware, disabling lock (20240827/evglock-59)
Fixes: 628c3bb40e9a8cefc0a6 ("LoongArch: Add boot and setup routines")
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Commit 5c83b07df9c5 ("tpm: Add a driver for Loongson TPM device") adds a
driver at drivers/char/tpm/tpm_loongson.c, and commit 74fddd5fbab8
("MAINTAINERS: Add entry for Loongson Security Engine drivers") adds a new
section LOONGSON SECURITY ENGINE DRIVERS intending to refer to that driver.
It however adds the entry drivers/char/tpm_loongson.c; note that it misses
the tpm subdirectory.
Adjust the entry to refer to the intended file.
Fixes: 74fddd5fbab8 ("MAINTAINERS: Add entry for Loongson Security Engine drivers")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Commit 5c83b07df9c5 ("tpm: Add a driver for Loongson TPM device") has a
semantic conflict with commit 07d8004d6fb9 ("tpm: add bufsiz parameter
in the .send callback"), as the former change was developed against a
tree without the latter change. This results in a build error:
drivers/char/tpm/tpm_loongson.c:48:17: error: initialization of 'int (*)(struct tpm_chip *, u8 *, size_t, size_t)' {aka 'int (*)(struct tpm_chip *, unsigned char *, long unsigned int, long unsigned int)'} from incompatible pointer type 'int (*)(struct tpm_chip *, u8 *, size_t)' {aka 'int (*)(struct tpm_chip *, unsigned char *, long unsigned int)'} [-Wincompatible-pointer-types]
48 | .send = tpm_loongson_send,
| ^~~~~~~~~~~~~~~~~
drivers/char/tpm/tpm_loongson.c:48:17: note: (near initialization for 'tpm_loongson_ops.send')
drivers/char/tpm/tpm_loongson.c:31:12: note: 'tpm_loongson_send' declared here
31 | static int tpm_loongson_send(struct tpm_chip *chip, u8 *buf, size_t count)
| ^~~~~~~~~~~~~~~~~
Add the expected bufsiz parameter to tpm_loongson_send() to resolve the
error.
Fixes: 5c83b07df9c5 ("tpm: Add a driver for Loongson TPM device")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
With new Loongson-3A6000/3C6000 hardware platforms (or later), hardware
page table walking (PTW) feature is supported on host. So here add this
feature detection on KVM host.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The clock controller of Loongson-2K0300 consists of three PLLs, requires
an 120MHz external reference clock to function, and generates clocks in
various frequencies for SoC peripherals.
Clock definitions for previous SoC generations could be reused for most
clock hardwares. There're two gates marked as critical, clk_node_gate
and clk_boot_gate, which supply the CPU cores and the system
configuration bus. Disabling them leads to a SoC hang.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Loongson-2K0300 requires a reference clock with a frequency different
from previous SoCs (120MHz v.s. 100MHz), thus hardcoding the firmware
name of the reference clock as ref_100m isn't a good idea.
This patch retrives the clock name of the reference clock dynamically
during probe, avoiding the hardcoded pdata structure and preparing for
support of future SoCs.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
LS2K0300 and LS2K0500 ship divider clocks which allows zero divisors,
in which case the divider acts the same as one is specified.
Let's pass CLK_DIVIDER_ALLOW_ZERO when registering divider clocks to
prepare for future introduction of these clocks.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
LS2K0300 and LS2K1500 ship scale clocks with an alternative mode.
There's one mode bit in clock configuration register indicating the
operation mode.
When mode bit is unset, the scale clock acts the same as previous
generation of scale clocks. When it's set, a different equation for
calculating result frequency, Fout = Fin / (scale + 1), is used.
This patch adds frequency calculation support for the scale clock
variant. A helper macro, CLK_SCALE_MODE, is added to simplify
definitions.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Some gate clocks need to be supplied with flags, e.g., it may be
required to specify CLK_IS_CRTICAL for CPU clocks.
Add a field to loongson2_clk_board_info for representing clock flags,
and specify it when registering gate clocks. A new helper macro,
CLK_GATE_FLAGS, is added to simplify definitions.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
In the majority, if not all cases, mac_interface and phy_interface
are the same with the exception of some drivers that I have suggested
only use phy_interface and set mac_interface to PHY_INTERFACE_MODE_NA.
The only two that currently set mac_interface to PHY_INTERFACE_MODE_NA
are dwmac-loongson and dwmac-lpc18xx, neither of which use RGMII nor
SGMII.
In order to phase out the use of mac_interface, we need to have a path
for existing drivers so they can update to only using phy_interface
without causing regressions.
Therefore, in order to keep the "pcs" code working, we need to choose
the STMMAC integrated PCS mode based on phy_interface if mac_interface
is PHY_INTERFACE_MODE_NA.
This will allow more drivers to set mac_interface to
PHY_INTERFACE_MODE_NA without risking regressions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1uytpG-00000006H29-1Ltk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Introduce acpi_gbl_use_global_lock, which allows to skip the Global Lock
initialization. This is useful for systems without Global Lock (such as
loong_arch), so as to avoid error messages during boot phase:
ACPI Error: Could not enable global_lock event (20240827/evxfevnt-182)
ACPI Error: No response from Global Lock hardware, disabling lock (20240827/evglock-59)
Link: https://github.com/acpica/acpica/commit/463cb0fe
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The Loongson-2K1000 NAND controller is also similar to the Loongson-1C.
It supports a maximum capacity of 16GB FLASH per chip with a maximum
page size of 8KB, and it supports up to 4 chip selects and 4 RDY
signals.
The key difference from the Loongson-2K0500 is that it requires explicit
configuration of the DMA control route. Typically, it is configured as
APBDMA0.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The Loongson-2K0500 NAND controller is similar to the Loongson-1C.
It supports a maximum capacity of 16GB FLASH per chip with a maximum
page size of 8KB, and it supports up to 4 chip selects and 4 RDY
signals.
Its DMA controller is defaulted to APBDMA0.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The page address register describes the page address of the starting
address for NAND read/write/erase operations.
According to the manual, it consists of two parts:
{chip select, page number}
The `chip select` is fixed at 2 bits, and the `page number` is
determined based on the actual capacity of the single-chip memory.
Therefore we need to determine the `chip select` bits base on the `page
number`.
For example, for a 1GB capacity chip (2K page size), it has 1M pages.
Thus, [19:0] is used to represent the page number, and [21:20]
represents the chip select.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Loongson-1C and Loongson-2K SoCs support NAND flash chips with 6-byte ID.
However, the current implementation only handles 5-byte ID which can lead
to incorrect chip detection.
Extend loongson_nand_read_id_type_exec() to support 6-byte NAND ID.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
I am going to introduce the NAND controllers of the Loongson-2K series
CPUs, which are similar to Loongson-1.
As preparation, rename all prefixes from Loongson1-specific to
Loongson-generic.
No functional change intended.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
On certain Loongson platforms, drivers attempting to request a legacy
ISA IRQ directly via request_irq() (e.g., IRQ 4) may fail. The
virtual IRQ descriptor is not fully initialized and lacks a valid irqchip.
This issue does not affect ACPI-enumerated devices described in DSDT,
as their interrupts are properly mapped via the GSI translation path.
This indicates the LPC irqdomain itself is functional but is not correctly
handling direct VIRQ-to-HWIRQ mappings.
The root cause is the use of irq_domain_create_linear(). This API sets
up a domain for dynamic, on-demand mapping, typically triggered by a GSI
request. It does not pre-populate the mappings for the legacy VIRQ range
(0-15). Consequently, if no ACPI device claims a specific GSI
(e.g., GSI 4), the corresponding VIRQ (e.g., VIRQ 4) is never mapped to
the LPC domain. A direct call to request_irq(4, ...) then fails because
the kernel cannot resolve this VIRQ to a hardware interrupt managed by
the LPC controller.
The PCH-LPC interrupt controller is an i8259-compatible legacy device
that requires a deterministic, static 1-to-1 mapping for IRQs 0-15 to
support legacy drivers.
Fix this by replacing irq_domain_create_linear() with
irq_domain_create_legacy(). This API is specifically designed for such
controllers. It establishes the required static 1-to-1 VIRQ-to-HWIRQ
mapping for the entire legacy range (0-15) immediately upon domain
creation. This ensures that any VIRQ in this range is always resolvable,
making direct calls to request_irq() for legacy IRQs function correctly.
Signed-off-by: Ming Wang <wangming01@loongson.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Loongson-2K0300 ships a GPIO controller whose input/output control logic
is similar to previous generation of SoCs. Additionally, it acts as an
interrupt-controller supporting both level and edge interrupts and has a
distinct reset signal.
Describe its compatible in devicetree. We enlarge the maximum value of
ngpios to 128, since the controller technically supports at most 128
pins, although only 106 are routed out of the package. Properties for
interrupt-controllers and resets are introduced and limited as LS2K0300
only.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250904013438.2405-2-ziyao@disroot.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The perf ilist command is a textual app [1] similar to perf list. In
the top-left pane a tree of PMUs is displayed. Selecting a PMU expands
the events within it. Selecting an event displays the `perf list`
style event information in the top-right pane.
When an event is selected it is opened and the counters on each CPU
the event is for are periodically read. The bottom of the screen
contains a scrollable set of sparklines showing the events in total
and on each CPU. Scrolling below the sparklines shows the same data as
raw counts. The sparklines are small graphs where the height of the
bar is in relation to maximum of the other counts in the graph.
By default the counts are read with an interval of 0.1 seconds (10
times per second). A -I/--interval command line option allows the
interval to be changed. The oldest read counts are dropped when the
counts fill the line causing the sparkline to move from right to left.
A search box can be pulled up with the 's' key. 'n' and 'p' iterate
through the search results. As some PMUs have hundreds of events a 'c'
key will collapse the events in the current PMU to make navigating the
PMUs easier.
[1] https://textual.textualize.io/
Committer testing:
This needs a bit more polishing, to test it I had to go thru some hops:
$ python ilist
python: can't open file '/home/acme/git/perf-tools-next/ilist': [Errno 2] No such file or directory
$
$ python tools/perf/python/ilist.py
Traceback (most recent call last):
File "/home/acme/git/perf-tools-next/tools/perf/python/ilist.py", line 8, in <module>
from textual import on
ModuleNotFoundError: No module named 'textual'
$
$ sudo dnf install textual
Updating and loading repositories:
Repositories loaded.
Failed to resolve the transaction:
No match for argument: textual
You can try to add to command line:
--skip-unavailable to skip unavailable packages
$
After some searching I installed the 'python3-textual' and it starts,
allowing traversing the various pmus and events, see descriptions on the
upper right side and a view of the events on the lower half of the
screen.
Interesting for quickly iterating thru the available events.
Reviewed-by: Howard Chu <howardchu95@gmail.com>
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Chun-Tse Shao <ctshao@google.com>
Cc: Collin Funk <collin.funk1@gmail.com>
Cc: Dr. David Alan Gilbert <linux@treblig.org>
Cc: Gautam Menghani <gautam@linux.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Falcon <thomas.falcon@intel.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Tiezhu Yang <yangtiezhu@loongson.cn>
Cc: Weilin Wang <weilin.wang@intel.com>
Cc: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250819013941.209033-6-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The default COMMAND_LINE_SIZE of 512, inherited from asm-generic, is
too small for modern use cases. For example, kdump configurations or
extensive debugging parameters can easily exceed this limit.
Therefore, increase the command line size to 4096 bytes, aligning
LoongArch with the MIPS architecture. This change follows a broader
trend among architectures to raise this limit to support modern needs;
for instance, PowerPC increased its value for similar reasons in the
commit a5980d064fe2 ("powerpc: Bump COMMAND_LINE_SIZE to 2048").
Similar to the change made for RISC-V in the commit 61fc1ee8be26
("riscv: Bump COMMAND_LINE_SIZE value to 1024"), this is considered
a safe change. The broader kernel community has reached a consensus
that modifying COMMAND_LINE_SIZE from UAPI headers does not constitute
a uABI breakage, as well-behaved userspace applications should not
rely on this macro.
Suggested-by: Huang Cun <cunhuang@tencent.com>
Signed-off-by: Ming Wang <wangming01@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
When compiling with LLVM and CONFIG_LTO_CLANG is set, there exist many
objtool warnings "sibling call from callable instruction with modified
stack frame".
For this special case, the related object file shows that there is no
generated relocation section '.rela.discard.tablejump_annotate' for the
table jump instruction jirl, thus objtool can not know that what is the
actual destination address.
It needs to do something on the LLVM side to make sure that there is the
relocation section '.rela.discard.tablejump_annotate' if LTO is enabled,
but in order to maintain compatibility for the current LLVM compiler,
this can be done in the kernel Makefile for now. Ensure it is aware of
linker with LTO, '--loongarch-annotate-tablejump' needs to be passed via
'-mllvm' to ld.lld.
Note that it should also pass the compiler option -mannotate-tablejump
rather than only pass '-mllvm --loongarch-annotate-tablejump' to ld.lld
if LTO is enabled, otherwise there are no jump info for some table jump
instructions.
Fixes: e20ab7d454ee ("LoongArch: Enable jump table for objtool")
Closes: https://lore.kernel.org/loongarch/20250731175655.GA1455142@ax162/
Reported-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Co-developed-by: WANG Rui <wangrui@loongson.cn>
Signed-off-by: WANG Rui <wangrui@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
If the MAC controller does not connect to any PHY interface, there is a
missing clock, then the DMA reset fails.
For this case, the DMA_BUS_MODE_SFT_RESET bit is 1 before software reset,
just print an error message which gives a hint the PHY clock is missing,
and then return -EINVAL immediately to avoid waiting for the timeout when
the DMA reset fails in loongson_dwmac_fix_reset().
With this patch, for the normal end user, the computer start faster with
reducing boot time for 2 seconds on the specified mainboard.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://patch.msgid.link/20250811073506.27513-4-yangtiezhu@loongson.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Binbin Zhou