Some gate clocks need to be supplied with flags, e.g., it may be
required to specify CLK_IS_CRTICAL for CPU clocks.
Add a field to loongson2_clk_board_info for representing clock flags,
and specify it when registering gate clocks. A new helper macro,
CLK_GATE_FLAGS, is added to simplify definitions.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
In the majority, if not all cases, mac_interface and phy_interface
are the same with the exception of some drivers that I have suggested
only use phy_interface and set mac_interface to PHY_INTERFACE_MODE_NA.
The only two that currently set mac_interface to PHY_INTERFACE_MODE_NA
are dwmac-loongson and dwmac-lpc18xx, neither of which use RGMII nor
SGMII.
In order to phase out the use of mac_interface, we need to have a path
for existing drivers so they can update to only using phy_interface
without causing regressions.
Therefore, in order to keep the "pcs" code working, we need to choose
the STMMAC integrated PCS mode based on phy_interface if mac_interface
is PHY_INTERFACE_MODE_NA.
This will allow more drivers to set mac_interface to
PHY_INTERFACE_MODE_NA without risking regressions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1uytpG-00000006H29-1Ltk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Introduce acpi_gbl_use_global_lock, which allows to skip the Global Lock
initialization. This is useful for systems without Global Lock (such as
loong_arch), so as to avoid error messages during boot phase:
ACPI Error: Could not enable global_lock event (20240827/evxfevnt-182)
ACPI Error: No response from Global Lock hardware, disabling lock (20240827/evglock-59)
Link: https://github.com/acpica/acpica/commit/463cb0fe
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The Loongson-2K1000 NAND controller is also similar to the Loongson-1C.
It supports a maximum capacity of 16GB FLASH per chip with a maximum
page size of 8KB, and it supports up to 4 chip selects and 4 RDY
signals.
The key difference from the Loongson-2K0500 is that it requires explicit
configuration of the DMA control route. Typically, it is configured as
APBDMA0.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The Loongson-2K0500 NAND controller is similar to the Loongson-1C.
It supports a maximum capacity of 16GB FLASH per chip with a maximum
page size of 8KB, and it supports up to 4 chip selects and 4 RDY
signals.
Its DMA controller is defaulted to APBDMA0.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The page address register describes the page address of the starting
address for NAND read/write/erase operations.
According to the manual, it consists of two parts:
{chip select, page number}
The `chip select` is fixed at 2 bits, and the `page number` is
determined based on the actual capacity of the single-chip memory.
Therefore we need to determine the `chip select` bits base on the `page
number`.
For example, for a 1GB capacity chip (2K page size), it has 1M pages.
Thus, [19:0] is used to represent the page number, and [21:20]
represents the chip select.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Loongson-1C and Loongson-2K SoCs support NAND flash chips with 6-byte ID.
However, the current implementation only handles 5-byte ID which can lead
to incorrect chip detection.
Extend loongson_nand_read_id_type_exec() to support 6-byte NAND ID.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
I am going to introduce the NAND controllers of the Loongson-2K series
CPUs, which are similar to Loongson-1.
As preparation, rename all prefixes from Loongson1-specific to
Loongson-generic.
No functional change intended.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
On certain Loongson platforms, drivers attempting to request a legacy
ISA IRQ directly via request_irq() (e.g., IRQ 4) may fail. The
virtual IRQ descriptor is not fully initialized and lacks a valid irqchip.
This issue does not affect ACPI-enumerated devices described in DSDT,
as their interrupts are properly mapped via the GSI translation path.
This indicates the LPC irqdomain itself is functional but is not correctly
handling direct VIRQ-to-HWIRQ mappings.
The root cause is the use of irq_domain_create_linear(). This API sets
up a domain for dynamic, on-demand mapping, typically triggered by a GSI
request. It does not pre-populate the mappings for the legacy VIRQ range
(0-15). Consequently, if no ACPI device claims a specific GSI
(e.g., GSI 4), the corresponding VIRQ (e.g., VIRQ 4) is never mapped to
the LPC domain. A direct call to request_irq(4, ...) then fails because
the kernel cannot resolve this VIRQ to a hardware interrupt managed by
the LPC controller.
The PCH-LPC interrupt controller is an i8259-compatible legacy device
that requires a deterministic, static 1-to-1 mapping for IRQs 0-15 to
support legacy drivers.
Fix this by replacing irq_domain_create_linear() with
irq_domain_create_legacy(). This API is specifically designed for such
controllers. It establishes the required static 1-to-1 VIRQ-to-HWIRQ
mapping for the entire legacy range (0-15) immediately upon domain
creation. This ensures that any VIRQ in this range is always resolvable,
making direct calls to request_irq() for legacy IRQs function correctly.
Signed-off-by: Ming Wang <wangming01@loongson.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
If the MAC controller does not connect to any PHY interface, there is a
missing clock, then the DMA reset fails.
For this case, the DMA_BUS_MODE_SFT_RESET bit is 1 before software reset,
just print an error message which gives a hint the PHY clock is missing,
and then return -EINVAL immediately to avoid waiting for the timeout when
the DMA reset fails in loongson_dwmac_fix_reset().
With this patch, for the normal end user, the computer start faster with
reducing boot time for 2 seconds on the specified mainboard.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://patch.msgid.link/20250811073506.27513-4-yangtiezhu@loongson.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Add the interrupt enable register offset (inten_offset) so that GPIO
interrupts can be enabled normally on more models.
According to the latest interface specifications, the definition of GPIO
interrupts in ACPI is similar to that in FDT. The GPIO interrupts are
listed one by one according to the GPIO number, and the corresponding
interrupt number can be obtained directly through the GPIO number
specified by the consumer.
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20250714064542.2276247-1-zhoubinbin@loongson.cn
[Bartosz: tweaked the commit message]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
'struct thermal_zone_device_ops' could be left unmodified in this driver.
Constifying this structure moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
This partly reverts commit 734b5def91b5 ("thermal/drivers/loongson2: Add
Loongson-2K2000 support") which removed the const qualifier. Instead,
define two different structures.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
5089 1160 0 6249 1869 drivers/thermal/loongson2_thermal.o
After:
=====
text data bss dec hex filename
5464 1128 0 6592 19c0 drivers/thermal/loongson2_thermal.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/5f5f815f85a9450bca7848c6d47a1fee840f47e5.1748176328.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Without correct unregisteration, ACPI notify handlers and the platform
drivers installed by generic_subdriver_init() will become dangling
references after removing the loongson_laptop module, triggering various
kernel faults when a hotkey is sent or at kernel shutdown.
Cc: stable@vger.kernel.org
Fixes: 6246ed09111f ("LoongArch: Add ACPI-based generic laptop driver")
Signed-off-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
loongson_laptop_turn_{on,off}_backlight() are designed for controlling
the power of the backlight, but they aren't really used in the driver
previously.
Unify these two functions since they only differ in arguments passed to
ACPI method, and wire up loongson_laptop_backlight_update() to update
the power state of the backlight as well. Tested on the TongFang L860-T2
Loongson-3A5000 laptop.
Cc: stable@vger.kernel.org
Fixes: 6246ed09111f ("LoongArch: Add ACPI-based generic laptop driver")
Signed-off-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Previously during driver probe, 1 is unconditionally taken as current
brightness value and set to props.brightness, which will be considered
as the brightness before suspend and restored to EC on resume. Since a
brightness value of 1 almost never matches EC's state on coldboot (my
laptop's EC defaults to 80), this causes surprising changes of screen
brightness on the first time of resume after coldboot.
Let's get brightness from EC and take it as the current brightness on
probe of the laptop driver to avoid the surprising behavior. Tested on
TongFang L860-T2 Loongson-3A5000 laptop.
Cc: stable@vger.kernel.org
Fixes: 6246ed09111f ("LoongArch: Add ACPI-based generic laptop driver")
Signed-off-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
After commit a934a57a42f64a4 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") and 7d95680d64ac8e836c ("scripts/misc-check:
check unnecessary #include <linux/export.h> when W=1"), we get some build
warnings with W=1:
drivers/spi/spi-loongson-core.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
So fix these build warnings for SPI/Loongson.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/20250608142939.172108-1-chenhuacai@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Add support for the stackleak feature. It initializes the stack with the
poison value before returning from system calls which improves the kernel
security.
At the same time, disables the plugin in EFI stub code because EFI stub
is out of scope for the protection.
Tested on Loongson-3A5000 (enable GCC_PLUGIN_STACKLEAK and LKDTM):
# echo STACKLEAK_ERASING > /sys/kernel/debug/provoke-crash/DIRECT
# dmesg
lkdtm: Performing direct entry STACKLEAK_ERASING
lkdtm: stackleak stack usage:
high offset: 320 bytes
current: 448 bytes
lowest: 1264 bytes
tracked: 1264 bytes
untracked: 208 bytes
poisoned: 14528 bytes
low offset: 64 bytes
lkdtm: OK: the rest of the thread stack is properly erased
Signed-off-by: Youling Tang <tangyouling@kylinos.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Add a new multi-chan IP core (0x12) support which is used in Loongson-
2K3000/Loongson-3B6000M. Compared with the 0x10 core, the new 0x12 core
reduces channel numbers from 8 to 4, but checksum is supported for all
channels.
Add a "multichan" flag to loongson_data, so that we can simply use a
"if (ld->multichan)" condition rather than the complicated condition
"if (ld->loongson_id == DWMAC_CORE_MULTICHAN_V1 || ld->loongson_id ==
DWMAC_CORE_MULTICHAN_V2)".
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Henry Chen <chenx97@aosc.io>
Tested-by: Biao Dong <dongbiao@loongson.cn>
Signed-off-by: Baoqi Zhang <zhangbaoqi@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Link: https://patch.msgid.link/20250424072209.3134762-3-chenhuacai@loongson.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: maoxiaochuan <maoxiaochuan@loongson.cn>
Yao Zi