优化架构

Bsp/Inc/Bsp.h

@@ -1,37 +1,11 @@
 #ifndef __BSP_H__
 #define __BSP_H__
 
-#include "VoiletTypeDef.h"
-
-/* Extra Library Enable */
-#define USE_SHELL       //系统使用Shell
-
-#ifdef USE_SHELL
-#include "LetterShell.h"
-#endif
-
-#define ARRAY_LEN(arr) (sizeof(arr) / sizeof((arr)[0]))
-
-/* BOOL类型定义 */
-typedef enum {
-    false = 0,
-    true  = 1,
-} bool_t;
-
-//GPIO
-//数组信号输入/出开关
-#define DI_ON       1
-#define DI_OFF      0
-#define DO_ON       1
-#define DO_OFF      0
-//LED灯开关
-#define LED_ON      0
-#define LED_OFF     1
-
-/* Voilet */
-void VoiletBspInit(void);
+/* Board */
+#include "Board.h"
 
 /* BSP */
+void BspInit(void);
 void LedOn(uint8_t Chnl);
 void LedOff(uint8_t Chnl);
 void LedSet(uint8_t Chnl,uint8_t Value);
@@ -39,8 +13,8 @@ void LedToggle(uint8_t Chnl);
 
 //Interrupt
 void IrqInit(void);
-void IrqRegister(unsigned int Irq, void(*Func)(void *Param));
-void IrqConfig(uint32_t Irq, uint8_t NvicPrePriority, uint8_t NvicSubPriority);
+void IrqRegister(unsigned char Irqn,void(*Func)(void *Param));
+void IrqEnable(uint32_t Irq, uint8_t NvicPrePriority, uint8_t NvicSubPriority);
 void IrqDisable(uint32_t Irq);
 
 //System Delay

Bsp/Inc/LetterShell.h

@@ -1,8 +0,0 @@
-#ifndef __LETTER_SHELL_H__
-#define __LETTER_SHELL_H__
-
-#include "Bsp.h"
-
-void LetterShellInit(const COM_MAP_T *ComX, uint32_t Baud);
-
-#endif

Bsp/Inc/VoiletPort.h

@@ -2,24 +2,53 @@
 // Created by anonymous on 2026/5/24.
 //
 
-#ifndef VOILETTYPEDEF_H
-#define VOILETTYPEDEF_H
+#ifndef _VOILET_PORT_H
+#define _VOILET_PORT_H
 
 #include "stm32f10x.h"
 
 #define INTERRUPT_ENABLE    __set_PRIMASK(0);       //开启中断
 #define INTERRUPT_DISABLE   __set_PRIMASK(1);       //关闭中断
 
+#define ARRAY_LEN(arr) (sizeof(arr) / sizeof((arr)[0]))
+
+/* BOOL类型定义 */
+typedef enum {
+    false = 0,
+    true  = 1,
+} BOOL_MAP_T;
+
+/* DI数字信号采集枚举 */
+enum {
+    DI_OFF = 0,
+    DI_ON
+};
+/* DO数字信号输出枚举 */
+enum {
+    DO_OFF = 0,
+    DO_ON
+};
+/* LED灯输出枚举 */
+enum {
+    LED_OFF = 0,
+    LED_ON
+};
+
+/* Interrupt Irq */
 typedef struct {
+    unsigned char Irqn;
+    void *Periph;
     void (*IrqCallback)(void *Param);
 }IRQ_MAP_T;
 
-#define IRQ_NUM 0xFF    //中断数量
+#define IRQ_NUM 67    //系统共有多少个中断
 #define NVIC_GROUP_LEVEL NVIC_PriorityGroup_2   //中断组
 
+/* GPIO */
 typedef struct {
     GPIO_TypeDef *GpioPort;
     unsigned short GpioPin;
+    // unsigned char Irqn;
 } GPIO_PERIPH_T;
 
 typedef struct {
@@ -28,6 +57,12 @@ typedef struct {
     GPIO_PERIPH_T Periph;
 } GPIO_MAP_T;
 
+typedef struct {
+    GPIO_MAP_T GpioX;
+    GPIOMode_TypeDef Mode;
+    GPIOSpeed_TypeDef Speed;
+}GPIO_CONFIG;
+
 // ==================== GPIOA 组 ====================
 #ifdef GPIOA
 #define GPIO0   {RCC_APB2PeriphClockCmd, RCC_APB2Periph_GPIOA, {GPIOA, GPIO_Pin_0}}
@@ -162,9 +197,12 @@ typedef struct {
 #define GPIO111 {RCC_APB2PeriphClockCmd, RCC_APB2Periph_GPIOG, {GPIOG, GPIO_Pin_15}}
 #endif
 
+#define GPIO_NULL    {0, 0, {0, 0}}
+
+/* COM */
 typedef struct {
     USART_TypeDef *UartId;
-    unsigned int Irqn;
+    unsigned char Irqn;
 } COM_PERIPH_T;
 
 typedef struct {
@@ -173,6 +211,14 @@ typedef struct {
     COM_PERIPH_T Periph;
 } COM_MAP_T;
 
+typedef struct {
+    COM_MAP_T *ComX;                //串口外设
+    GPIO_MAP_T TxPort;              //发送端口
+    GPIO_MAP_T RxPort;              //接收端口
+    GPIO_MAP_T TxRxEn;              //收发使能
+}COM_CONFIG;
+
+#define COM_NUM 5
 #ifdef USART1
 #define COM0   (&(COM_MAP_T){RCC_APB2PeriphClockCmd, RCC_APB2Periph_USART1, {USART1,USART1_IRQn}})
 #endif
@@ -187,4 +233,4 @@ typedef struct {
 #endif
 #define COM4   (&(COM_MAP_T){RCC_APB1PeriphClockCmd, RCC_APB1Periph_UART5,{UART5,UART5_IRQn}})
 
-#endif //VOILETTYPEDEF_H
+#endif //_VOILET_PORT_H

Bsp/Src/Bsp.c

@@ -1,151 +1,186 @@
 #include "Bsp.h"
 
-//
-// #ifdef USE_DIGITAL_OUTPUT
-//     GPIO_ST DigiTalOutPut[DO_NUM] =
-//     {
-//         GPIOB,GPIO_Pin_8,RESET,
-//     };
-// #endif
-//
-// #ifdef USE_DIGITAL_INPUT
-//     GPIO_ST DigiTalInPut[DI_NUM] =
-//     {
-//         GPIOF,GPIO_Pin_8,SET,
-//         GPIOE,GPIO_Pin_4,SET,
-//         GPIOE,GPIO_Pin_3,SET,
-//     };
-// #endif
-//
-// //LED灯数组
-// #ifdef USE_LED
-//     GPIO_ST DigiTalLed[LED_NUM] =
-//     {
-//         GPIOB,GPIO_Pin_5,SET,
-//         GPIOE,GPIO_Pin_5,SET,
-//     };
-// #endif
-//
-// /**
-//  * @brief  BSP的配置和初始化
-//  * @param  void
-//  * @retval void
-//  * @note   void
-//  * @example void
-//  */
-// void BspInit(void)
-// {
-//     //关闭所有系统中断
-//     INTERRUPT_DISABLE
-//
-//     //System Delay
-//     SystemDelayConfig();
-//
-//     //Interrupt
-//     SystemInterruptInit();
-//
-//     //Gpio
-//     SystemGpioInit();
-//
-//     {
-//         //DO
-//         #ifdef USE_DIGITAL_OUTPUT
-//         for (uint8_t i = 0; i < DO_NUM; i++) {
-//             GpioConfig(DigiTalOutPut[i].GpioPort,DigiTalOutPut[i].GpioPin,GPIO_Mode_Out_PP,GPIO_Speed_50MHz);
-//             GpioSetSts(DigiTalOutPut[i].GpioPort,DigiTalOutPut[i].GpioPin,DigiTalOutPut[i].DefaultStatus);
+#ifdef TTY_COM
+#include "LetterShell.h"
+#endif
+
+// LED灯数组
+#if (LED_NUM != 0)
+const GPIO_CONFIG LED_PERIPH[] = {
+    {.GpioX = GPIO21, .Mode = GPIO_Mode_Out_PP, .Speed = GPIO_Speed_10MHz},
+    {.GpioX = GPIO69, .Mode = GPIO_Mode_Out_PP, .Speed = GPIO_Speed_10MHz},
+};
+#endif
+//数字输入数组
+#if (DI_NUM != 0)
+const GPIO_CONFIG DI_PERIPH[] = {
+    {},
+};
+#endif
+//数字输出数组
+#if (DO_NUM != 0)
+const GPIO_CONFIG DO_PERIPH[] = {
+    {},
+};
+#endif
+//串口配置表
+const COM_CONFIG COM_PERIPH[] = {
+    {COM0,.TxPort = GPIO9, .RxPort =GPIO10},
+    {COM1,.TxPort = GPIO2, .RxPort = GPIO3,.TxRxEn = GPIO55},
+};
+
+void BspExtraInit(void);
+
+/**
+ * @brief  Voilet BSP的初始化函数
+ * @note  void
+ * @param void
+ * @retval void
+ */
+void BspInit(void) {
+    unsigned char i = 0;
+
+    INTERRUPT_DISABLE
+
+    //初始化中断系统
+    IrqInit();
+
+    //初始化延时库
+    DelayConfig();
+
+    //LED灯配置
+#if (LED_NUM != 0)
+    for (i = 0;i < ARRAY_LEN(LED_PERIPH);i++) {
+        //配置GPIO口
+        GpioConfig(&LED_PERIPH[i].GpioX, LED_PERIPH[i].Mode, LED_PERIPH[i].Speed);
+    }
+#endif
+
+    //DI采集配置
+#if (DI_NUM != 0)
+    // for (i = 0;i < DI_NUM;i++) {
+    //     //打开外设时钟
+    //     GpioClockEnable(&LED_PERIPH[i].GpioX);
+    //     //配置GPIO口
+    //     GpioConfig(&LED_PERIPH[i].GpioX, LED_PERIPH[i].Mode, LED_PERIPH[i].Speed);
     // }
-//         #endif
-//         //DI
-//         #ifdef USE_DIGITAL_INPUT
-//         for (uint8_t i = 0; i < DI_NUM; i++) {
-//             GpioConfig(DigiTalInPut[i].GpioPort,DigiTalInPut[i].GpioPin,GPIO_Mode_IPU,GPIO_Speed_50MHz);
-//         }
-//         #endif
-//         //LED
-//         #ifdef USE_LED
-//         for (uint8_t i = 0; i < LED_NUM; i++) {
-//             GpioConfig(DigiTalLed[i].GpioPort,DigiTalLed[i].GpioPin,GPIO_Mode_Out_PP,GPIO_Speed_50MHz);
-//             GpioSetSts(DigiTalLed[i].GpioPort,DigiTalLed[i].GpioPin,DigiTalLed[i].DefaultStatus);
-//         }
-//         #endif
-//     }
-//
-//     //Usart
-//     SystemUsartInit();
-//
-//     {
-//         //串口的TX引脚需要复用推挽模式，RX引脚需要浮空输入模式
-//         #ifdef USE_USART1
-//             GpioConfig(COM0_TX_PORT,COM0_TX_PIN,GPIO_Mode_AF_PP,GPIO_Speed_50MHz);
-//             GpioConfig(COM0_RX_PORT,COM0_RX_PIN,GPIO_Mode_IPU,GPIO_Speed_50MHz);
-//         #endif
-//         #ifdef USE_USART2
-//             GpioConfig(COM1_TX_PORT,COM1_TX_PIN,GPIO_Mode_AF_PP,GPIO_Speed_50MHz);
-//             GpioConfig(COM1_RX_PORT,COM1_RX_PIN,GPIO_Mode_IPU,GPIO_Speed_50MHz);
-//         #endif
-//         #ifdef USE_USART3
-//             GpioConfig(COM2_TX_PORT,COM2_TX_PIN,GPIO_Mode_AF_PP,GPIO_Speed_50MHz);
-//             GpioConfig(COM2_RX_PORT,COM2_RX_PIN,GPIO_Mode_AF_PP,GPIO_Speed_50MHz);
-//         #endif
-//         #ifdef USE_USART4
-//             GpioConfig(COM3_TX_PORT,COM3_TX_PIN,GPIO_Mode_AF_PP,GPIO_Speed_50MHz);
-//             GpioConfig(COM3_RX_PORT,COM3_RX_PIN,GPIO_Mode_AF_PP,GPIO_Speed_50MHz);
-//         #endif
-//         #ifdef USE_USART5
-//             GpioConfig(COM4_TX_PORT,COM4_TX_PIN,GPIO_Mode_AF_PP,GPIO_Speed_50MHz);
-//             GpioConfig(COM4_RX_PORT,COM4_RX_PIN,GPIO_Mode_AF_PP,GPIO_Speed_50MHz);
-//         #endif
-//     }
-//
-//     #ifdef EXTRA_BSP
-//     BspExtraInit();
-//     #endif
-// }
-//
-// void SystemStart(void)
-// {
-//     //开启系统中断
-//     INTERRUPT_ENABLE
-//
-//     #ifdef USE_RTOS
-//         #ifdef USE_FREERTOS
-//         #endif
-//         #ifdef USE_UCOS
-//         #endif
-//         #ifdef USE_THREADX
-//         #endif
-//     #endif
-// }
-//
-// /**
-//  * @brief  扩展库初始化
-//  * @param  void
-//  * @retval void
-//  * @note   理论上扩展库要在BSP的最后加载
-//  * @example void
-//  */
-// void BspExtraInit(void)
-// {
-//     //LetterShell初始化
-//     #ifdef USE_SHELL
-//         LetterShellInit(TTY_COM,TTY_BAUD);
-//     #endif
-// }
-//
-// //用户层接口
-// void BspSystemReboot(void)
-// {
-//     INTERRUPT_DISABLE
-//     NVIC_SystemReset(); // 执行软件复位
+#endif
+
+    //DO输出配置
+#if (DO_NUM != 0)
+    // for (i = 0;i < DO_NUM;i++) {
+    //     //打开外设时钟
+    //     GpioClockEnable(&LED_PERIPH[i].GpioX);
+    //     //配置GPIO口
+    //     GpioConfig(&LED_PERIPH[i].GpioX, LED_PERIPH[i].Mode, LED_PERIPH[i].Speed);
     // }
+#endif
+
+    //串口配置
+    for (i = 0;i < ARRAY_LEN(COM_PERIPH);i++) {
+        GpioConfig(&COM_PERIPH[i].TxPort, GPIO_Mode_AF_PP, GPIO_Speed_2MHz);
+        GpioConfig(&COM_PERIPH[i].RxPort, GPIO_Mode_IPU, GPIO_Speed_2MHz);
+    }
+
+    INTERRUPT_ENABLE
+
+    BspExtraInit();
+}
+
+/**
+ * @brief  扩展库初始化
+ * @note  理论上扩展库要在BSP的最后加载
+ * @param  void
+ * @retval void
+ */
+void BspExtraInit(void)
+{
+    //LetterShell初始化
+#ifdef TTY_COM
+    LetterShellInit(TTY_COM,TTY_BAUD);
+#endif
+}
+
+/**
+ * @brief  打开LED灯
+ * @note   void
+ * @param  Chnl 通道
+ * @retval void
+ */
+void LedOn(uint8_t Chnl)
+{
+    if (Chnl >= LED_NUM)
+        return;
+    GpioSet(&LED_PERIPH[Chnl].GpioX, RESET);
+}
+/**
+ * @brief  关闭LED灯
+ * @note   void
+ * @param  Chnl 通道
+ * @retval void
+ */
+void LedOff(uint8_t Chnl)
+{
+    if (Chnl >= LED_NUM)
+        return;
+    GpioSet(&LED_PERIPH[Chnl].GpioX, SET);
+}
+
+void LedSet(uint8_t Chnl,uint8_t Value)
+{
+    if (Chnl >= LED_NUM)
+        return;
+    if (Value == LED_ON) {
+        GpioSet(&LED_PERIPH[Chnl].GpioX, RESET);
+    }
+    else {
+        GpioSet(&LED_PERIPH[Chnl].GpioX, SET);
+    }
+}
+
+/**
+ * @brief  切换LED灯状态
+ * @note   void
+ * @param  Chnl 通道 Status 状态
+ * @retval void
+ */
+void LedToggle(uint8_t Chnl)
+{
+    if (Chnl >= LED_NUM)
+        return;
+    if (GpioGet(&LED_PERIPH[Chnl].GpioX) == LED_ON)
+    {
+        GpioSet(&LED_PERIPH[Chnl].GpioX,LED_OFF);
+    }
+    else
+    {
+        GpioSet(&LED_PERIPH[Chnl].GpioX,LED_ON);
+    }
+}
+
+void Rs485StdConfig(const COM_MAP_T *ComX,unsigned int Baud)
+{
+    for (unsigned char i = 0;i < ARRAY_LEN(COM_PERIPH);i++) {
+        if (ComX == COM_PERIPH[i].ComX) {
+            if (COM_PERIPH[i].TxRxEn.ClockTree) {
+                GpioSet(&COM_PERIPH[i].TxRxEn,Baud);
+            }
+            ComStdConfig(COM_PERIPH[i].ComX,Baud);
+        }
+    }
+}
+
+void Rs485AdvConfig(const COM_MAP_T *ComX, uint32_t Baud, uint8_t DataBits, uint8_t StopBits, uint8_t Parity)
+{
+
+}
+
 /**
 * @brief 重写Printf函数
 * @note void
 * @param void
 * @retval void
 */
-//  ||
-//     #include <SysCall.c>
 #if defined(__CC_ARM) || defined(__CLANG_ARM)
 int fputc(int ch, FILE *f)
 {

Bsp/Src/Interrupt.c

@@ -1,8 +1,8 @@
+#include <stddef.h>
+
 #include "Bsp.h"
 
-#define IRQ_NULL ((void *)0)
-
-IRQ_MAP_T IRQ_PERIPH[IRQ_NUM] = {0x00};
+IRQ_MAP_T IRQ_PERIPH[IRQ_NUM];
 
 /**
  * @brief 中断回调函数初始化为空
@@ -15,19 +15,18 @@ void IrqInit(void)
     //设定系统中断组
     NVIC_PriorityGroupConfig(NVIC_GROUP_LEVEL);
     for (uint8_t i = 0; i < IRQ_NUM; i++) {
-        IRQ_PERIPH[i].IrqCallback = IRQ_NULL;
+        IRQ_PERIPH[i].IrqCallback = NULL;
     }
 }
-
 /**
  * @brief 中断回调函数注册
  * @note 将外部传入的函数地址关联到INTERRUPT_ST表中
  * @param Vector:中断号 void(*Func)(uint32_t):回调函数
  * @retval void
  */
-void IrqRegister(unsigned int Irq, void(*Func)(void *Param))
-{
-    IRQ_PERIPH[Irq].IrqCallback = Func;
+void IrqRegister(unsigned char Irqn,void(*Func)(void *Param)) {
+    IRQ_PERIPH[Irqn].Irqn = Irqn;
+    IRQ_PERIPH[Irqn].IrqCallback = Func;
 }
 
 /**
@@ -36,7 +35,7 @@ void IrqRegister(unsigned int Irq, void(*Func)(void *Param))
  * @param Vector:中断号 NvicPrePriority:主优先级 NvicSubPriority:抢占优先级
  * @retval void
  */
-void IrqConfig(uint32_t Irq, uint8_t NvicPrePriority, uint8_t NvicSubPriority)
+void IrqEnable(uint32_t Irq, uint8_t NvicPrePriority, uint8_t NvicSubPriority)
 {
     NVIC_InitTypeDef NVIC_InitStructure;
 
@@ -59,17 +58,17 @@ void IrqDisable(uint32_t Irq)
    NVIC_InitStructure.NVIC_IRQChannel = Irq;
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
-   NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
+   NVIC_InitStructure.NVIC_IRQChannelCmd = DISABLE;
    NVIC_Init(&NVIC_InitStructure);
 }
 
 void USART1_IRQHandler(void)
 {
+    if (IRQ_PERIPH[COM0->Periph.Irqn].IrqCallback != NULL) {
         if (USART_GetFlagStatus(COM0->Periph.UartId, USART_FLAG_ORE) == SET)
         {
             USART_ClearFlag(COM0->Periph.UartId, USART_FLAG_ORE);
         }
-    if (IRQ_PERIPH[COM0->Periph.Irqn].IrqCallback != IRQ_NULL) {
         IRQ_PERIPH[COM0->Periph.Irqn].IrqCallback(COM0);
     }
 }
@@ -80,7 +79,7 @@ void USART2_IRQHandler(void)
     {
         USART_ClearFlag(COM1->Periph.UartId, USART_FLAG_ORE);
     }
-    if (IRQ_PERIPH[COM1->Periph.Irqn].IrqCallback != IRQ_NULL) {
+    if (IRQ_PERIPH[COM1->Periph.Irqn].IrqCallback != NULL) {
         IRQ_PERIPH[COM1->Periph.Irqn].IrqCallback(COM1);
     }
 }
@@ -91,8 +90,8 @@ void USART3_IRQHandler(void)
     {
         USART_ClearFlag(COM2->Periph.UartId, USART_FLAG_ORE);
     }
-    if (IRQ_PERIPH[COM2->Periph.Irqn].IrqCallback != IRQ_NULL) {
-        IRQ_PERIPH[COM2->Periph.Irqn].IrqCallback(COM1);
+    if (IRQ_PERIPH[COM2->Periph.Irqn].IrqCallback != NULL) {
+        IRQ_PERIPH[COM2->Periph.Irqn].IrqCallback(COM2);
     }
 }
 
@@ -103,7 +102,7 @@ void USART4_IRQHandler(void)
     {
         USART_ClearFlag(COM3->Periph.UartId, USART_FLAG_ORE);
     }
-    if (IRQ_PERIPH[COM3->Periph.Irqn].IrqCallback != IRQ_NULL) {
+    if (IRQ_PERIPH[COM3->Periph.Irqn].IrqCallback != NULL) {
         IRQ_PERIPH[COM3->Periph.Irqn].IrqCallback(COM3);
     }
 }
@@ -114,7 +113,7 @@ void USART5_IRQHandler(void)
     {
         USART_ClearFlag(COM4->Periph.UartId, USART_FLAG_ORE);
     }
-    if (IRQ_PERIPH[COM4->Periph.Irqn].IrqCallback != IRQ_NULL) {
+    if (IRQ_PERIPH[COM4->Periph.Irqn].IrqCallback != NULL) {
         IRQ_PERIPH[COM4->Periph.Irqn].IrqCallback(COM4);
     }
 }

Bsp/Src/LetterShell.c

@@ -1,102 +0,0 @@
-#include "LetterShell.h"
-#include "shell.h"
-/* 板级BSP头文件 */
-#include "Bsp.h"
-#include "Voilet.h"
-
-#define WR_BUFFER_SIZE    512
-
-/* 1. 创建shell对象，开辟shell缓冲区 */
-Shell Host;                        //Shell实例化
-char HostBuffer[WR_BUFFER_SIZE];   //读写缓冲区
-const COM_MAP_T *HostCom = TTY_COM;
-/**
- * @brief  Shell写函数
- * @param  ComId 串口号，ch 数据
- * @retval void
- * @note   void
- * @example void
- */
-signed short ShellWrite(char* ch, unsigned short Len)
-{
-    ComSendStr(HostCom, (uint8_t* )ch,Len);
-    return Len;
-}
-/**
- * @brief  Shell读函数 - 中断回调实现
- * @param  Vector 中断向量号
- * @retval void
- * @note   void
- * @example void
- */
-void LetterShellIrqFunc(void *Param)
-{
-    uint8_t ch = 0x00;
-    ch = ComReceiveChar(Param);
-    shellHandler(&Host, ch);
-}
-
-
-/**
- * @brief  初始化Shell
- * @param  ComId 串口号，baud 波特率
- * @retval void
- * @note   void
- * @example void
- */
-void LetterShellInit(const COM_MAP_T *ComX, uint32_t Baud)
-{
-    //初始化串口
-    ComStdConfig(ComX, Baud);
-    //设置串口回调函数
-    IrqRegister(ComX->Periph.Irqn, LetterShellIrqFunc);
-    //设置中断等级
-    IrqConfig(ComX->Periph.Irqn,1,1);
-    //注册写函数
-    Host.write = ShellWrite;
-    //初始化LetterShell
-    shellInit(&Host, HostBuffer, WR_BUFFER_SIZE);
-}
-
-// /**
-//  * @brief  打印版本号
-//  * @param  void
-//  * @retval void
-//  * @note   void
-//  * @example void
-//  */
-// void version(void)
-// {
-//     printf("%s,%s\r\n",HARDWARE_VERSION,SOFTWARE_VERSION);
-// }
-//
-// /**
-//  * @brief  重启单片机
-//  * @param  void
-//  * @retval void
-//  * @note   void
-//  * @example void
-//  */
-// void reboot(void)
-// {
-//     SystemReboot();
-// }
-//
-// /**
-//  * @brief  串口测试程序
-//  * @param  void
-//  * @retval void
-//  * @note   void
-//  * @example void
-//  */
-//
-// void comTest(uint8_t ComId)
-// {
-// }
-//
-// //打印版本号
-// SHELL_EXPORT_CMD(SHELL_CMD_PERMISSION(0)|SHELL_CMD_TYPE(SHELL_TYPE_CMD_FUNC), version, version, version);
-// //软重启单片机
-// SHELL_EXPORT_CMD(SHELL_CMD_PERMISSION(0)|SHELL_CMD_TYPE(SHELL_TYPE_CMD_FUNC), reboot, reboot, reboot);
-// //串口测试
-// SHELL_EXPORT_CMD(SHELL_CMD_PERMISSION(0)|SHELL_CMD_TYPE(SHELL_TYPE_CMD_FUNC), comTest, comTest, comTest);

Bsp/Src/SeggerCall.c

@@ -16,7 +16,7 @@ Purpose : Implementation of low-level functions for I/O with the
 *
 **********************************************************************
 */
-#ifdef defined (__SEGGER__)
+#if defined (__SEGGER__)
 #include "__SEGGER_RTL_Int.h"
 #include "stdio.h"
 #include "Bsp.h"

Bsp/Src/SysCall.c

@@ -20,7 +20,7 @@
  *
  ******************************************************************************
  */
-#ifdef defined (__GNUC__)
+#if defined (__GNUC__)
 /* Includes */
 #include "Bsp.h"
 
@@ -69,7 +69,7 @@ __attribute__((weak)) int _write(int file, char *ptr, int len)
   */
 PUTCHAR_PROTOTYPE
 {
-  UsartSendChar(TTY_COM, ch); //阻塞式无限等待
+  ComSendChar(TTY_COM, ch); //阻塞式无限等待
   return ch;
 }
 
@@ -83,8 +83,7 @@ PUTCHAR_PROTOTYPE
 GETCHAR_PROTOTYPE
 {
   uint8_t ch = 0;
-  ch = UsartReceiveChar(TTY_COM);
-    
+  ch = ComReceiveChar(TTY_COM);
   return ch;
 }
 

Bsp/Src/Uart.c

@@ -1,5 +1,7 @@
 #include "Bsp.h"
 
+extern const COM_CONFIG COM_PERIPH[];
+
 /**
  * @brief  初始化UART口外设的时钟
  * @note  void
@@ -92,3 +94,7 @@ void ComAdvConfig(const COM_MAP_T *ComX, uint32_t Baud, uint8_t DataBits, uint8_
 {
     ComInit(ComX, Baud, DataBits, StopBits, Parity);
 }
+
+unsigned int CalcBaudTransIoSpeed(unsigned int Baud) {
+
+}